background image

29 / 37

Normal

Intern

al Use

Confidential □ Re

stricted Confidential

User Manual

Antenna location is important; we recommend directing the antenna away from high-speed

switching signals. Furthermore, the trace from the module to the antenna should be as
short as possible and must be shielded by complete grounding.

The M14Q2SG is well shielded; the high-speed elements on a system should have shielding

reserved during the early stages of development.

3.5. Radiated sensitivity measurement

Over-the-air testing can demonstrate the TRX ability of the whole system. Keys elements that affect the
measurement are:

Module ability (refer Specification)
Antenna Gain
System noise source

The OTA performance should be performed in an OTA chamber.

3.6. GNSS external circuit design

One GNSS SAW filter, LNA, and another GNSS SAW filter need to be used between the module and
antenna.

in129 GPIO05Pin129 GPI

3.7. Supported frequencies

Table 5. Band support

Band

Uplink (MHz)

Downlink (MHz)

LTE Band 2

1,850–1,910

1,930–1,990

LTE Band 4

1,710–1,755

2,110–2,155

LTE Band 5

824–849

869–894

LTE Band 12

699–716

729–746

LTE Band 25

1,850-1,915

1,930-1,995

LTE Band 26

814-849

859-894

Band

Uplink (MHz)

Downlink (MHz)

WCDMA Band 2

1,850–1910

1,930–1,990

WCDMA Band 5

824–849

869–894

Summary of Contents for M14Q2SG






































Reviews: