background image

82

User Manual WMF 1500 S

Care | Manual cleaning

6.5.10  Clean the bean hopper

The bean hoppers should be cleaned as required and at 
regular intervals. Recommendation: monthly.

risk of injury

•  Long hair could become caught in the 

grinder head and drawn into the coffee 
machine.

 

> Always protect hair with a hairnet before 

removing the bean hopper.

  

Bruising or crushing hazard /  

risk of injury

•  The coffee machine contains moving parts 

that can cause finger or hand injury.

 

> Always switch off the coffee machine and 

unplug the mains plug before reaching into 
the coffee grinder or the opening of the 
brewing unit.

  

 

> Never clean the bean hoppers in 

a dishwasher.

  

 

™

Slide the operating panel upward

The ON/OFF switch is on the right side, behind the 
operating panel.

 

™

Press the ON/OFF switch until coffee machine 
switches off

 

™

Disconnect mains plug

 

™

Use the multitool to turn the lock on the bean 
hopper counterclockwise to open it

 

™

Lift bean hoppers out

 

™

Completely empty bean hoppers and wipe out 
thoroughly with a damp cloth

 CaUtion

 CaUtion

iMportant

Rotate the lock by 90°

Summary of Contents for 1500S













































































































Reviews: