WMF 1300 S User Manual Download

Page: 97 / 136

User Manual WMF 1300 S

Care | Manual cleaning

7.5.3 Clean the brewing unit

Pinching or crushing hazard /

risk of injury

• The coffee machine contains moving parts

that can cause finger or hand injury.

• There is a risk of pinching when removing

the brewing unit.

> Always switch off the coffee machine and

unplug the mains plug before reaching into
the coffee grinder or the opening of the
brewing unit.

> Hold the brewing unit tightly and remove it

carefully.

The brewing unit should be cleaned when needed and
at regular intervals.

Press the ON/OFF switch until coffee machine
switches off

Disconnect mains plug

Push combi spout all the way up

Remove grounds container

Remove the drip tray

Brewing unit is now fully accessible.

Burn hazard

• The brewing unit can still be hot immediately

after switching off.

> Allow the coffee machine to cool before

cleaning.

•  The brewing unit can slip downwards.
>  Always hold the brewing unit securely.
>  Never use force. Danger of breakage.

CAUTION

Follow the Safety chapter

starting on page 5

CAUTION

Follow the Safety chapter

starting on page 5

IMPORTANT

Follow the Warranty chapter

starting on page 124

Summary of Contents for 1300 S









































































































































Search results

Summary of Contents for 1300 S

Reviews:

Related manuals for 1300 S

Brands by name

Popular brands

WMF 1300 S, User Manual

Search results

Summary of Contents for 1300 S

Reviews:

Related manuals for 1300 S

Brands by name

Popular brands