background image

English _

15

 

!

NETWORK CONNECTION AND SETUP

PORT RANGE FORWARD (PORT MAPPING) SETUP

If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the 
Broadband Router so that a remote PC can access the camera in it.

Manual Port Range Forwarding

1. 

From the Setup menu of the Broadband Router, select 
<

Applications & Gaming

> - <

Port Range Forward

>. 

For setting the port range forward for a third-party Broadband 
Router, refer to the user guide of that Broadband Router.

2. 

Select <

TCP

> and <

UDP Port

> for each connected camera 

to the Broadband Router. 
The number of each port to be configured to the IP router 
should be set according to the port number designated 
in <

Setup

> - <

Basic

> - <

IP & Port

> on the camera web 

viewer.

3. 

When done, click [

Save Settings

].  

Your settings will be saved.

 

M

 

`

Port forwarding setting is an example of setting CISCO IP router.

 

`

The settings may differ depending on the connected Broadband Router model. 
For more information, refer to the user manual of the applicable router.

Setting up Port Range Forward for several network cameras

 

~

You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. 

 

~

A user can change each port using the camera setting screen.

When Camera1 and Camera2 are connected to a router :

User

Internet

Broadband Router

Start

End

Protocol

IP Address

3000

3000

TCP/UDP

192.168.1.100

3001

3001

TCP/UDP

192.168.1.101

8080

8080

TCP/UDP

192.168.1.100

8081

8081

TCP/UDP

192.168.1.101

Camera1 (192.168.1.100)

HTTP port

8080

RTSP port

3000

Camera2 (192.168.1.101)

HTTP port

8081

RTSP port

3001

 

M

 

`

Port forwarding can be done without additional router setup if the router supports the UPnP (Universal Plug and Play) function. 
After connecting the network camera, select the checkbox from the menu <

Quick connect

> in <

Wisenet DDNS

> in 

Settings

 

;

 

Network

 

;

 

DDNS

”.

Summary of Contents for TNO-6322ER






















Reviews: