Wisenet TNF-9010 User Manual Download Page 10 | Manualshive

Page: 10 / 28

background image

10_

installation & connection

installation & connection

INSTALLATION

Precautions before installation

Ensure you read out the following instructions before installing the camera:

~

Select an installation site that can hold at least 5 times the camera’s weight.

~

Stuck-in or peeled-off cables can cause damage to the product or a fire.

~

For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case.

~

If the product is installed with excessive force, it may cause damage to the camera due to malfunction.
Forcing assembly using non-compliant tools may damage the product.

Disassembling

1.

Peel off the tape that holds the mount plate and camera body, and detach the mount plate.

2.

Turn the top cover in the direction of the arrow to remove it.

3.

Peel off the camera lens protective film.

«
...
8
9
10
11
12
...
»

Summary of Contents for TNF-9010





























Reviews:

No comments

Related manuals for TNF-9010

Brand: Ecco Pages: 15

Brand: Jäger Direkt Pages: 5

Brand: FootfallCam Pages: 4

Brand: Elko Pages: 5

Brand: Speco Pages: 2

Brand: Basalte Pages: 2

Brand: Foscam Pages: 70

Brand: Uniden Pages: 66

Brand: CAMDEN Pages: 2

Brand: DELTA DORE Pages: 2

Brand: IDS Pages: 8

XRX300 LED Series

Brand: WE-EF Pages: 6

Brand: MeiTrack Pages: 8

Brand: i-onyx Pages: 34

Brand: Koukaam Pages: 23

Brand: Dorlen Pages: 2

ViP2 VK2-1080VFD3V9F

Brand: Vista Pages: 12

Leak Alert WiFi

Brand: Zircon Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands