background image

network connection and setup

14_

 network connection and setup

network connection and setup

You can set up the network settings according to your network configurations.

CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING

Connecting to the camera from a local PC in the LAN

1. 

Launch an Internet browser on the local PC.

2. 

Enter the IP address of the camera in the address bar of the browser.

 

M

 

`

A remote PC in an external Internet out of the LAN network may not be able to connect to the camera installed in the intranet 
if the port-forwarding is not properly set or a firewall is set. 
In this case, to resolve the problem, contact your network administrator.

 

`

By factory default, the IP address will be assigned from the DHCP server automatically. 
If there is no DHCP server available, the IP address will be set to 192.168.1.100. 
To change the IP address, use the Device Manager. 
For further details on Device Manager use, refer to “

Using Device Manager

”. (Page 15)

CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE 
MODEM

1. 

Connect the user PC directly with the network camera.

2. 

Run the Device Manager and change the IP address of the camera so that you can use the web browser 
on your desktop to connect to the camera.

3. 

Use the Internet browser to connect to the web viewer. 

4. 

Move to [

Setup

] page.

5. 

Move to [

Network

] – [

DDNS

] and configure the DDNS settings.

6. 

Move to [

Basic

] – [

IP & Port

], and set the IP type to [

DHCP

].

7. 

Connect the camera, which was removed from your PC, directly to the modem.

8. 

Restart the camera.

 

M

 

`

For information on how to set DDNS, refer to the online help of Web Viewer.

 

`

For information on how to set the IP format, refer to the online help of Web Viewer.

<Local Network>

Camera

Camera

Local PC

INTERNET

External Remote PC

DDNS Server 
(Data Center, KOREA)

Camera

External Remote PC

DDNS Server 
(Data Center, KOREA)

DSL/Cable Modem

INTERNET

Summary of Contents for QNP-6320HS
























Reviews: