Wireless ACW/LW8-DIND160 Page 2 User Manual Download

Page: 2 / 41

ACW-DINDxxx_UG_EN_V1.8

Table of content

DOCUMENT VERSION HISTORY....................................................................................................................................... 3

DISCLAIMER ..................................................................................................................................................................... 3

TRADEMARKS AND COPYRIGHT ...................................................................................................................................... 3

DECLARATION OF COMPLIANCE ..................................................................................................................................... 4

ENVIRONMENTAL RECOMMENDATIONS ....................................................................................................................... 4

XPLOSIVE ATMOSPHERE

.......................................................................................................................................... 4

NVIRONMENT

....................................................................................................................................................... 4

ADIO

................................................................................................................................................................... 5

PRELUDE ........................................................................................................................................................................... 6

PRODUCT IDENTIFICATION ............................................................................................................................................. 7

TECHNICAL FEATURES ............................................................................................................................................ 8

RODUCTS FEATURES

............................................................................................................................................... 8

LECTRICAL FEATURES

.............................................................................................................................................. 9

NPUTS AND COUNTERS FEATURES

........................................................................................................................... 10

EMPERATURE SENSOR FEATURES

............................................................................................................................ 10

ETERS BACK

.................................................................................................................................................. 10

UTPUTS CALENDAR

.............................................................................................................................................. 10

FOOTPRINT AND MOUNTING .............................................................................................................................. 12

SET UP ................................................................................................................................................................... 13

NTENNA POSITIONING

.......................................................................................................................................... 13

ODEM CONNECTION

........................................................................................................................................... 13

Antenna (SMA connector) .................................................................................................................................... 13

Jack connector ...................................................................................................................................................... 13

Micro USB ............................................................................................................................................................. 13

ERMINALS

’

DESCRIPTION

....................................................................................................................................... 14

USHBUTTON

....................................................................................................................................................... 15

LED

S MEANING

.................................................................................................................................................... 15

NORMAL BEHAVIOR AT STARTUP ........................................................................................................................ 16

SETUP AND CONFIGURATION .............................................................................................................................. 17

ETUP

................................................................................................................................................................. 17

Inputs setup .......................................................................................................................................................... 17

Available event .................................................................................................................................................................... 17

Pulling types (from version V1.2.0) .................................................................................................................................... 17

Available trigger modes ...................................................................................................................................................... 17

Bounce time parameter........................................................................................................................................ 18

Periodic frame parameter .................................................................................................................................... 18

Keep alive frame parameters ............................................................................................................................... 18

The available periods are as follows .................................................................................................................................. 18

Temperature parameter (offset) .......................................................................................................................... 18

Pairing method setup ........................................................................................................................................... 18

ONFIGURATION VIA

USB ...................................................................................................................................... 19

UPLINKS ON IOT NETWORKS (SIGFOX/LORAWAN)............................................................................................. 22

EST FRAME

......................................................................................................................................................... 22

Summary of Contents for ACW/LW8-DIND160










































Search results

Summary of Contents for ACW/LW8-DIND160

Reviews:

Related manuals for ACW/LW8-DIND160

Brands by name

Popular brands

Wireless ACW/LW8-DIND160, User Manual

Search results

Summary of Contents for ACW/LW8-DIND160

Reviews:

Related manuals for ACW/LW8-DIND160

Brands by name

Popular brands