background image

1128500

WPC 2000 User Manual

A-6

Extracts from OSHA and ANSI

Extracts from ANSI B11.1-2009   8.6.2.1

Standards Requirements

Explanatory Information

8.6.2.1.7  Each operator’s hand controls shall be 
located at a distance from the point-of-operation 
so that the operator(s) cannot release either 
hand actuating control and reach into the point-
of-operation during the hazardous portion of the 
cycle.

E8.6.2.1.7  The total stopping time of the press 
should include the total response time of the 
control system and the time it takes hazardous 
motion to stop.  The following formula should be 
used when calculating the safety distance (Ds):

Ds =  K (Ts + Tc + Tbm)

Where:

K = 63 inches/second (hand speed constant).

Ts  = the stop time of the press measured from 
the final de-energized control element, usually 
the air valve.

Tc = the response time of the control.

Tbm = the additional time allowed by the 
stopping-performance monitor (brake monitor) 
before it detects stop time deterioration.

NOTE – Ts + Tc are usually measured by a stop 
time measuring device.

When the press stopping-performance monitor 
setting is changed, the safety distance should 
be recalculated.  See also Annex C.

Summary of Contents for wpc 2000



























































































































































































































































Reviews: