Wintriss Shadow VI User Manual Download Page 29

Page: 29 / 159

Shadow VI User Manual

1107200

Installation and Checkout

Chapter 2

page 17

Installation Procedure

DANGER

FAILURE TO PERFORM SAFETY SYSTEM TESTS

•

Perform the final checkout sequence below when you have completed installation of your

light curtain, before operating the equipment it is connected to.

•

Operate your machinery only after your safety system meets all the requirements of the

checkout sequence.

•

Perform the final checkout sequence whenever repair, maintenance or modification is

performed on your light curtain or the machinery it is connected to.

•

Perform the “daily test” safety system checkout sequence on page 93 (in French, en

Français, page 114) every day before operating any machinery connected to Shadow safety
light curtains.

Failure to comply with these instructions will result in death or serious injury.

WARNING

ELECTRIC SHOCK HAZARD

•

Turn off and disconnect power from the Shadow safety light curtain and from the machinery

it is connected to before making any wiring connections. This includes disconnecting power
to the machine control and motor.

•

Remove all fuses and “tag out” per OSHA 1910.147 Control of Hazardous Energy

(Lockout/Tagout).

•

Ensure that installation is performed by qualified personnel.

Failure to comply with these instructions could result in death or serious injury.

The installation procedure is divided into these steps:

• Calculating the safety distance

• Designing and mounting brackets

• Loosely mounting Shadow VI heads

•

Mounting the control

• Wiring the transmitter and receiver to the control

•

Connecting AC wiring to the control

• Connecting stop circuits to the control

• Making settings inside the control

• Aligning and tightening down Shadow VI components

•

Diagnostic steps to perform

before

Shadow operation

• Final checkout sequence

It is a good idea to read over the complete installation procedure before starting. This will
guide you about the materials and techniques required for making and positioning mounting
brackets and aligning Shadow VI heads.

Summary of Contents for Shadow VI
































































































































































Search results

Summary of Contents for Shadow VI

Reviews:

Related manuals for Shadow VI

Brands by name

Popular brands

Wintriss Shadow VI, User Manual

Search results

Summary of Contents for Shadow VI

Reviews:

Related manuals for Shadow VI

Brands by name

Popular brands