Wintriss Shadow VI User Manual Download Page 105 | Manualshive

Page: 105 / 159

background image

Shadow VI User Manual

1107200

Excerpts from OSHA Regulations and

Appendix A

page 93

ANSI Standards
Daily Tests in French and English

Appendix A – Extracts from OSHA
Regulations and ANSI Standards

WARNING

!

REFER TO CURRENT REVISIONS OF OSHA/ANSI DOCUMENTS

The following extracts from OSHA and ANSI documents are provided for the user’s
convenience only. Refer to the most recent revisions of the original OSHA safety regulations
and ANSI standards to ensure that you have the most up-to-date information.

Failure to comply with these instructions could result in death or serious injury.

This appendix provides extracts from the Occupational Safety and Health Administration
(OSHA) regulations and the American National Standards Institute (ANSI) standards
covering presence-sensing devices.

Extracts from OSHA Regulation 1910.217

WARNING

!

REFER TO CURRENT REVISIONS OF OSHA/ANSI DOCUMENTS

The following extracts from OSHA and ANSI documents are provided for the user’s
convenience only. Refer to the most recent revisions of the original OSHA safety regulations
and ANSI standards to ensure that you have the most up-to-date information.

Failure to comply with these instructions could result in death or serious injury.

Reprinted below are extracts from OSHA regulation 1910.217 pertaining to the use of
presence-sensing devices for point-of-operation guarding on mechanical power presses.
Also reprinted here are interpretations of selected regulations provided by the Precision
Metalforming Association (PMA). Extracts from the OSHA regulation are printed in the
left-hand column; interpretations by PMA are shown in the right-hand column.

Wintriss makes no claim for the accuracy or effectiveness of the PMA interpretations, and
persons making use of this material do so at their own risk. PMA interpretations should not
be relied upon for use in any specific application. The material is provided, with PMA’s
permission, for informational purposes only.

Refer to the most recent versions of OSHA documents. To obtain copies of OSHA
regulations, write to: OSHA’s Office of Information and Consumer Affairs, 200 Constitution
Avenue NW, Room N3647, Washington, DC 20210. Tel (202) 219-8151; fax (202) 219-
5986.

«
...
103
104
105
106
107
...
»

Summary of Contents for Shadow VI
































































































































































Reviews:

No comments

Related manuals for Shadow VI

Brand: Faller Pages: 4

Brand: Happybeds Pages: 5

Brand: feather&black Pages: 4

Brand: EAST COAST Pages: 12

Brand: EAST COAST Pages: 5

Brand: EAST COAST Pages: 10

Brand: Gardenline Pages: 15

Brand: Garderline Pages: 13

Brand: IBM Pages: 4

Brand: Laufen Pages: 2

Brand: Okamura Pages: 12

Brand: ofichairs Pages: 2

Brand: Acadia Pages: 2

Brand: Gautier Pages: 16

Brand: Enwork Pages: 14

HAMPTON SOFA SET CORNER

Brand: Emmezeta Pages: 10

Brand: World Market Pages: 4

Sierra 2-Leg Desk SEHX30-48 Series

Brand: Workrite Ergonomics Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands