Winterthur Gas & Diesel Ltd. X52 Operation Manual Download

Page: 476 / 519

Tab 12-12 Specifications for HFO

Parameter

Bunker limit

At engine inlet

Unit

Test method

Kinematic viscosity
at 50°C

Maximum 700

13 to 17

(not related

to temperature)

/s [cSt]

ISO 3104

Density at 15°C

Maximum 1010

kg/m

ISO 3675/12185

CCAI

Maximum 870

Calculated

Sulphur

Statutory specifica-
tions

Maximum 3.5

mass %

ISO 8754/14596

Flash point

Minimum 60

°C

ISO 2719

Hydrogen sulphide

Maximum 2.0

mg/kg [ppm]

IP 570

Acid number

Maximum 2.5

mg KOH/g

ASTM D 664

Total sediment,
aged

Maximum 0.1

mass %

ISO 10307-2

Carbon residue: mi-
cro method

Maximum 20

mass %

ISO 10370

Pour point (upper)

Maximum 30

°C

ISO 3016

Water

Maximum 0.5

Maximum 0.2

volume %

ISO 3733

Ash

Maximum 0.15

mass %

ISO 6245

Vanadium

Maximum 450

mg/kg [ppm]

ISO 14597/IP501/
IP470

Sodium

Maximum 100

Maximum 30

mg/kg [ppm]

IP501/IP470

Aluminum plus Sili-
con

Maximum 60

Maximum 15

mg/kg [ppm]

ISO 10478/IP501/
IP470

Used lubricating oils
(ULO) must not be
present: Calcium
(Ca) and zinc (Zn)

ULO shows if: Ca>30
and Zn>15 or Ca>30
and P>15

Do no use if: Ca>30
and Zn>15 or Ca>30
and P>15

mg/kg [ppm]

IP501 or IP470 or
IP500

For RT-flex and X-engines, the fuel viscosity at the engine inlet must be in the range between
10 mm

/s and 20 mm

/s, but WinGD recommends a fuel viscosity at the engine inlet in the

range between 13 mm

/s and 17 mm

/s. The maximum permitted temperature is 150°C.

1 mm

/s = 1 cSt (Centistoke)

The maximum limit is 991 kg/m

if the fuel treatment plant cannot remove water from high-

density fuel.

In ISO 8217:2017 sulphur limits are not given. Sulphur limits are related to statutory
specifications.

The hydrogen sulphide limit is applicable from 1 July 2012.

Purchasers must make sure that the equipment on board can always keep the fuel at a
temperature above the pour point, specially in cold climates.

It is very important that the fuel is fit for purpose in the related engine application.

X52

AA00-0000-00AAA-030A-A

Operation Manual

Diesel engine fuels

Winterthur Gas & Diesel Ltd.

- 476 -

Issue 002 2018-11

Summary of Contents for X52








































































































































































































































































































































































































































































































































Search results

Summary of Contents for X52

Reviews:

Related manuals for X52

Brands by name

Popular brands

Winterthur Gas & Diesel Ltd. X52, Operation Manual

Search results

Summary of Contents for X52

Reviews:

Related manuals for X52

Brands by name

Popular brands