WinSystems EBC-C413 Product Manual Download Page 39

Page: 39 / 83

EBC-C413/Configuration

v1.2

www.winsystems.com

Page 39

WINSYSTEMS cable CBL-PWR-117-12 simplifies this connection to the

board.

7.12.16 FAN - Connector for Optional Fan

The FAN connector provides output power and control for an optional

fan.

Layout and Pin Reference

This connection is a Molex 22-11-2042 (or equivalent).

Matching connectors:

• Molex 22-01-2045 (housing)
• Molex 08-55-0110 or 08-55-0111 (crimp)

The FAN connector is pin compatible with Standard PC chassis 3-pin or 4-

pin fans.

7.12.17 LVDS - LVDS Display Output Connector

The EBC-C413 supports low-voltage differential signaling (LVDS) for flat-

panel displays with resolutions up to 1920 x 1200 at 24 bpp.

NOTE The EBC-C413 has one VGA, one Mini DisplayPort and one Low-Voltage

Differential Signaling (LVDS) interface. Only two of the three outputs may

be active simultaneously.

The power (SWVDD) portion of this connector can be configured (see

“JPLCDP - LCD Panel Power Configuration” on page 53). Connect to the

LVDS interface through the LVDS connector.

Pin 1

WIRE LIST

J1 J2 COLOR SIGNAL

1 5 12

2 2 BLACK GND

3 4 BLACK GND

4 3

RED

+ 5 V

Pin

Name

GND (Ground)

12 V

RPM

CTRL

Summary of Contents for EBC-C413




















































































Search results

Summary of Contents for EBC-C413

Reviews:

Brands by name

Popular brands

WinSystems EBC-C413, Product Manual

Search results

Summary of Contents for EBC-C413

Reviews:

Brands by name

Popular brands