manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 756

14.1.2

Crank angle sensor unit (flywheel) - proximity sensor - install

Periodicity

Description

Unscheduled
Duration for performing preliminary requirements

0.0 man-hours

Duration for performing the procedure

0.5 man-hours

Duration for performing the requirements after job completion

0.0 man-hours

Personnel

Description

Specialization

QTY

Engine crew

Basic

AR

Support equipment

Description

Part No.

CSN

QTY

None

Supplies

Description

QTY

None

Spare Parts

Description

Part No.

CSN

QTY

proximity sensor

A/R

SAFETY PRECAUTIONS

•

None

PRELIMINARY OPERATIONS

•

The engine must be stopped and made safe for maintenance.

X82-B

AA00-9223-01AAA-720B-A

Maintenance Manual

Crank angle sensor unit (flywheel) - proximity sensor - install

Winterthur Gas & Diesel Ltd.

- 756 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands