WinGD X82-B Maintenance Manual Download Page 600

Page: 600 / 841

10.7

Supply unit

10.7.1

Supply unit camshaft and bearing shell - prepare before
removal

Periodicity

Description

Working hours

90000

Support equipment

Description

Part No.

CSN

QTY

roller lifting tool

94569B

Supplies

Description

QTY

None

Spare Parts

Description

Part No.

CSN

QTY

None

SAFETY PRECAUTIONS

•

None

PRELIMINARY OPERATIONS

•

The engine must be stopped and made safe for maintenance.

X82-B

AA00-5581-01AAA-523A-A

Maintenance Manual

Supply unit camshaft and bearing shell - prepare before removal

Winterthur Gas & Diesel Ltd.

- 600 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands