manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 218

7.1.5

Cylinder liner - grind the lubricating groove

Periodicity

Description

Unscheduled

as necessary

Duration for performing preliminary requirements

0.0 man-hours

Duration for performing the procedure

1.0 man-hours

Duration for performing the requirements after job completion

0.0 man-hours

Personnel

Description

Specialization

QTY

Engine crew

Basic

1

Support equipment

Description

Part No.

CSN

QTY

None

Supplies

Description

QTY

Oil stone

1

Emery cloth

A/R

Spare Parts

Description

Part No.

CSN

QTY

None

SAFETY PRECAUTIONS

WARNING

Before you operate the turning gear, make sure that no personnel are near the flywheel,
or in the engine.

PRELIMINARY OPERATIONS

•

The cylinder cover must be removed, refer to section 

7.4.1 Cylinder cover - remove

X82-B

AA00-2124-00AAA-655B-A

Maintenance Manual

Cylinder liner - grind the lubricating groove

Winterthur Gas & Diesel Ltd.

- 218 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands