manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 200

7.1

Cylinder liner

7.1.1

Cylinder liner - do a check of the bore

Periodicity

Description

Unscheduled

After each piston removal and

installation

Duration for performing preliminary requirements

0.0 man-hours

Duration for performing the procedure

1.0 man-hours

Duration for performing the requirements after job
completion

0.0 man-hours

Personnel

Description

Specialization

QTY

Engine crew

Basic

2

Support equipment

Description

Part No.

CSN

QTY

Inside micrometer

94101

1

Ladder

94224

1

Gauge

94225

1

Supplies

Description

QTY

None

Spare Parts

Description

Part No.

CSN

QTY

None

SAFETY PRECAUTIONS

WARNING

Gas Hazard: Poisonous gas can stay in the cylinder liner. There is a risk of suffocation.
You must make sure that poisonous gas is removed before you go into the cylinder liner.
You must put on a harness attached to a safety person before you do work in cylinders
where gas can stay.

WARNING

Injury Hazard: Before you operate the turning gear, make sure that no personnel are near
the flywheel, or in the engine.

X82-B

AA00-2124-00AAA-360A-A

Maintenance Manual

Cylinder liner - do a check of the bore

Winterthur Gas & Diesel Ltd.

- 200 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands