manualshive.com logo in svg

WinGD X72-B, Operation Manual

Share
Download
WinGD X72-B Operation Manual Download Page 58

2.7

Access to engine spaces

Periodicity

Description

Unscheduled

Duration for performing preliminary requirements

0.0 man-hours

Duration for performing the procedure

0.5 man-hours

Duration for performing the requirements after job completion

0.0 man-hours

Personnel

Description

Specialization

QTY

Engine crew

Basic

1

Support equipment

Description

Part No.

CSN

QTY

None

Supplies

Description

QTY

None

Spare Parts

Description

Part No.

CSN

QTY

None

SAFETY PRECAUTIONS

WARNING

Injury Hazard: Be careful of the slippery and sharp edges inside the engine spaces.

PRELIMINARY OPERATIONS

•

The engine must be stopped and prepared for maintenance, refer to section 

8.18 Prepare

the engine after stop - general

X72-B

AA00-0000-00AAA-012E-A

Operation Manual

Access to engine spaces

Winterthur Gas & Diesel Ltd.

- 58 -

Issue 003  2021-12

Summary of Contents for X72-B















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands