manualshive.com logo in svg

WinGD X72-B, Operation Manual

Share
Download
WinGD X72-B Operation Manual Download Page 475

Fig 10-19

 Turbocharger cut out procedure: Illustration 5

NOTE:

If during the one of the procedures mentioned in this chapter, an auxiliary blower
becomes inoperative, it will automatically be cut out thanks to the built in non-return
valve. This will restrict the operation of the engine.

X72-B

AA00-0000-00AAB-100A-A

Operation Manual

Special running condition: Turbocharger cut out

Winterthur Gas & Diesel Ltd.

- 475 -

Issue 003  2021-12

Summary of Contents for X72-B















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands