manualshive.com logo in svg

WinGD X62DF, Maintenance Manual

Share
Download
WinGD X62DF Maintenance Manual Download Page 476

8.7.2

Piston - prepare before removal

Periodicity

Description

Working hours

36 000

Duration for performing preliminary requirements

0.0 man-hours

Duration for performing the procedure

1.0 man-hours

Duration for performing the requirements after job completion

0.0 man-hours

Support equipment

Description

Part No.

CSN

QTY

Lifting tool

94209

1

Distance holder

94230

2

Piston suspension device

94341

1

Plate

94341A

2

Supplies

Description

QTY

Oil

A/R

Spare Parts

Description

Part No.

CSN

QTY

None

SAFETY PRECAUTIONS

WARNING

Injury Hazard: Before you operate the turning gear, make sure that no personnel are near
the flywheel, or inside the engine.

PRELIMINARY OPERATIONS

•

The cylinder cover must be removed, refer to section 

7.5.1 Cylinder cover - remove

•

The engine temperature must be cool.

X72DF

AA00-3403-00AAA-523A-A

Maintenance Manual

Piston - prepare before removal

Winterthur Gas & Diesel Ltd.

- 476 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands