Wincor Nixdorf TH210 Programmer'S Manual Download Page 28

Page: 28 / 152

TH210

Programmer’s Guide

Command conventions

The following information describes how each command is organized:

Name:

Name of command.

ASCII:

The ASCII control code.

Hexadecimal:

The hexadecimal control code.

Decimal:

The decimal control code.

Value:

A description of the command operands.

Range:

The upper and lower limits of the command operand.

Default:

The command operand default after printer reset.

Description:

Brief description and summary of the command.

Formulas:

Any formulas used for this command.

Exceptions:

Describes any exceptions to this command; for example, incompatible
commands.

Relate
information:

Describes related information for this command; for example, bit
information.

Command descriptions

Printer actions

The printer function commands control the following basic printer functions and are described in
order of their hexadecimal codes:



Resetting the printer



Cutting the paper



Opening the cash drawers

Clear printer

ASCII

DLE

Hexadecimal

Decimal

Clears the print line buffer without printing and sets the printer to the following condition:



Double-wide command (0x12) is cancelled



Line spacing, pitch, and user-defined character sets are maintained at current

selections (RAM is not affected)



Single-wide, single-high, non-rotated, and left-aligned characters are set



Printing position is set to column one

Related Information

This command followed by a 04 or 05 is interpreted as a “Real Time Command”.
This command is recognized in A793 emulation and Native mode, ignored in LEGACY emulation.

Summary of Contents for TH210

























































































































































Search results

Summary of Contents for TH210

Reviews:

Related manuals for TH210

Brands by name

Popular brands

Wincor Nixdorf TH210, Programmer'S Manual

Search results

Summary of Contents for TH210

Reviews:

Related manuals for TH210

Brands by name

Popular brands