Wincor Nixdorf TH210 Programmer'S Manual Download Page 12 | Manualshive

Page: 12 / 152

background image

TH210

Programmer’s Guide

8

Communication interface settings

To change the communication interface settings, enter the configuration menu, select “Set
Communication Interface” from the main menu.

Caution:

Be extremely careful changing any of the printer settings to avoid inadvertently changing

other settings that might affect the performance of the printer.
Press the paper feed button as instructed on the configuration menu to select the settings you
want to change.



Baud rate

115200 baud
57600 baud
38400 baud
19200 baud
9600 baud
4800 baud
2400 baud
1200 baud



Parity

No Parity
Even Parity
Odd Parity



Flow control methd

Software (XON/XOFF)
Hardware (DTR/DSR)



Data reception errors

Ignore errors
Print “?”



Alternate DTR/DSR

Enabled
Disabled



USB Driver

Printer Cass
Comm Class



USB NAK

Reject Packets When Error
Accept Packets When Error

Note: Press the paper feed button for at least one second to validate the selection.

Setting the RS-232C Serial interface settings

Refer to the section “Configuring the printer”.

Diagnostics modes

To change the the diagnostic modes enter the configuration menu, select “Set Diagnostics Modes”
from the main menu and select one of the following modes:



Normal: normal operating mode of the printer.



Datascope: the receipt printer prints incoming commands and data in hexadecimal

format to help troubleshoot communication problems. There are DataScope modes
for both with and without graphics.



Receipt test: the receipt printer prints all code pages to verify proper printing of the

receipt.

Caution: Be extremely careful changing any of the printer settings to avoid inadvertently changing
other settings that might affect the performance of the printer.
Refer to the section “Configuring the printer,” for instructions on how to enter the configuration
menu.

«
...
10
11
12
13
14
...
»

Summary of Contents for TH210

























































































































































Reviews:

No comments

Related manuals for TH210

Brand: Oki Pages: 40

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 97

SCX 4828FN - Laser Multi-Function Printer

Brand: Samsung Pages: 151

SCX 4725FN - B/W Laser - All-in-One

Brand: Samsung Pages: 120

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 97

SCX 4200 - B/W Laser - All-in-One

Brand: Samsung Pages: 95

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 172

ProXpress M337x

Brand: Samsung Pages: 56

PROXPRESS M332 SERIES

Brand: Samsung Pages: 50

ML-2240 - 23 Ppm Mono Laser Printer

Brand: Samsung Pages: 82

Brand: Samsung Pages: 8

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 134

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 112

Brand: Samsung Pages: 128

Brand: Samsung Pages: 152

ML 3471ND - B/W Laser Printer

Brand: Samsung Pages: 207

ML 2150 - B/W Laser Printer

Brand: Samsung Pages: 237

ML 3471ND - B/W Laser Printer

Brand: Samsung Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands