Wincomm Technologies Corp. WAF2400-1000L Installation And Operation Manual Download Page 1

1

Product code WAF2400-1000L
Antenna Amplifier, 2.4-2.4835 GHz, 0.250 W Output

Caution:

   For use only with the provided Lucent Technologies  

ORiNOCO  

Model:  PC24E

-

00-FC WaveLAN

 

2.4 GHz

wireless card with  FCC ID: IMRWLPC24.  Use of other radio transmitters with this amplifier may cause interference, and
is a violation of  FCC Rules.

The bi-directional RF amplifier greatly increases usable signal transmission range by increasing receiver sensitivity and
compensating for various line losses (in the feeder, connectors and cable) and signal losses due to electromagnetic
radiation.

Receiver Performance

Maximum Gain: 22dB
Noise Figure: 2.8 dB
Frequency Response: +/- 0.5 dB over operating range
Output Saturation RF Power: 10 mW

Transmitter Performance

Automatic Gain Control
Maximum Gain: 30 dB
Intput RF Power: 0.5 - 100 mW
Maximum Output RF Power: 250 mW

Input/Output Impedance: 50 Ohm
Switching Power: 0.2 - 0.4 mW
Switch Delay Time: 0.5 - 0.8 mks
Input/Output Connectors: N – Type Female
Operating Temperature: -50°C - +50°C

Power Supply Specifications

Input Voltage: 110 - 240 VAC 50/60 Hz
Output Voltage/Power: 12 VDC / 10 W

DC Power Injector

:

- Radio Modem Connector: N – Type Female
- Amplifier Connector: N – Type Female
- 12 VDC Power Input Connector: BNC - Type Female

Filter Specifications

Filter Bandwidth: 100 MHz
RF Range: 2.4 - 2.5 GHz
Insertion Loss in 2.4-2.5 GHz: 0.5 dB
Signal Attenuation: 50 dB @ 2 GHz
Signal Attenuation: 50 dB @ 3 GHz

Physical Characteristics

Amplifier Weight: 2.0 lbs (0.9 kg)
Amplifier Dimensions: 12 in x 4.8 in x 2.8 in (300mm x 120mm x 70mm)
Power Supply Weight: 1.0 lb (0.45 kg)
Power Supply Dimensions: 12 in x 4.8 in x 2.8 in (300mm x 120mm x 70mm)

Summary of Contents for WAF2400-1000L






Reviews: