Tel: 973-916-9958
Fax: 973-916-9959
Address: 65 Industrial Road, Lodi, NJ 07644
Website: http://www.wincous.com
STEP 1
TOOLS
You will need these tools to assemble the high-chair (model #: CHH-25)
STEP 2
Align the two (2) chair cross braces so they
can be pushed into place over the screw
bosses as shown (Image A).
NOTE:
The cross brace with the
notches will be the front
of the fully assembled chair.
STEP 5
Installing the Leg Divider T-Bar:
Secures the front of the seat.
Position the Leg Divider T-Bar with the
curved middle facing forward. (Image H)
Insert the bottom of the vertical middle
tab into the opening on the seat. Take the
two raised pins with the brass threaded
inserts (found at both ends of leg divider
bar) and push them into the holes on both
sides of the chair.
Align the holes on the top front leg sides
with the holes of the Leg Divider T-Bar
and use the M5 x 40mm screws with the
washers provided to tighten both sides
securely (Image I).
STEP 6
Caster wheel and insert assembly
Push the four (4) plastic molded inserts
firmly into the base of the chair legs. Use
rubber mallet if necessary.
Carefully insert metal shafts of the caster
wheels into the inserts.
Stand high-chair up on wheels to make
sure casters are locked in place.
This completes the high-chair assembly.
Phillips
Screwdriver
Rubber Mallet
Eye Protection
Six (6) M6 x 40mm Screws
and Washers
One (1) Molded Seat
Image A
Image B
Image H
Image C
Image I
Two (2) Chair Cross Braces
One (1) Adjustable Food Tray
One (1) Leg Divider & Restraint
Two (2) Molded Chair Leg Sides
Molded Inserts
Four (4)
Caster Wheels
Four (4)
OPTIONAL |
Two (2) M5 x 40mm
Screws & Washers
Two (2) M5 x 20mm Screws,
Washers & Hex Nuts
Fourteen (14) -
Hole Plug Caps
Cleaning and Maintenance
Limpieza y mantenimiento
Nettoyage et entretien
Reinigung und Wartung
Pulizia e manutenzione
Reinigen en onderhoud
Rengoring öch underhåll
Wash chair as needed with a
mild soap and water solution.
Do not use solvents or harsh
petrol Chemicals cleaners.
Lave la silla según sea necesario
con una solución de agua y
jabón suave. No use solventes
o limpiadores Petroquímicos
agresivos
Lavez la chaise aubesoin avec
une solution de savon doux et
d’eau. N’utilisez pas de solvants
ou de nettoyants chimiques à
l’essence forts.
Den Stuhl mit Wasser
und einem milden
Reinigungsmittel reinigen.
Keine Lösungsmittel oder
aggressive Reinigungsmittel
auf Mineralölbasis verwenden.
Lavare il seggiolone secondo
necessità con detergente
delicate in soluzione acquosa.
Non usare solventi o detergenti
chimici aggressivi.
Was de stoel zo nodig met een
oplossing van water en zachtz
zeep. Geen oplosmiddelen
of scherpe petrochemische
reinigingsmiddelen gebruiken.
Tvätta stolenvid behov med
en mild tvål upplöst I vatten.
Använd inte lösningsmedel
eller starka kemikalier
rengöringsmedel.
Check that all screws and
fittings are correctly and
tightly fitted before and
during use.
Verifique que todos los tornillos
y accesorios estén colocados
y apretados adecuadamente
antes de usar la silla.
Vor und während der
Verwendung sollte derfeste
Sitz der Schrauben und
Beschläge überprüft warden.
Controllare che viterie e
accessory siano corret tamente
montati e serrate,prima e
durante l’uso.
Controleer dat alle schroeven
en fittingen behoorlijk en
stevig vast zitten vóór en
tijdens gebruik.
Kontrollera att alla skruvar och
beslag är ordentligt fästa före
och under använding.
STEP 3
After both chair braces are pushed firmly into place (Image B),
use the four (4) M6 x 40mm screws and washers to secure
assembly (Image C).
Screw Boss
STEP 4
Seat Installation:
Place the seat into the position as shown
(Image D) and insert
the raised screw bosses
(Image E) into the holes
on either side of the legs.
Use two (2) M5 x 36mm
screws on each side to
secure the seat (Image F).
After tightening these
screws, insert the two hex nuts provided
into the hex shaped recesses found on the
opposite top REAR leg sides (Image G)
MAKE SURE THAT THE HEX NUTS ARE
PLACED WITH THE FLAT SIDE OF THE
NUT TO THE INSIDE OF HEX HOLES
Push the seat back to its horizontal
position (Image D) so that the holes in the
rear of the seat align themselves over the
holes where you’ve placed the hex nuts.
Use two (2) M5 x 20 screws with the
washers provided to secure the REAR of
the seat to the legs.
NOTE:
Make sure holes line up when inserting
screws. Some downward pressure on seat
may be needed.
Image E
Raised Screw Boss
Image J
PARTS
Check to make
sure you have all
the parts shown.
Image F
Image G
Insert
Tab
Push brass
pins into
holes
PUSH
Image D
Push seat back in di-
rection of arrow after
securing with screws
as shown in Image F.
CHH-25
OPTIONAL |
CASTERS & MOLDED INSERTS
SOLD SEPARATELY
CASTERS & MOLDED INSERTS SOLD SEPARATELY
