Winbond W632GU6NB Series General Description Manual Download Page 5 | Manualshive

Page: 5 / 162

background image

W632GU6NB

Publication Release Date: Aug. 20, 2018

Revision: A01

- 5 -

1. GENERAL DESCRIPTION

The W632GU6NB is a 2G bits DDR3L SDRAM, organized as 16,777,216 words



8

banks



16 bits.

This device achieves high speed transfer rates up to 2133 MT/s (DDR3L-2133) for various
applications. This device is sorted into the following speed grades: -09, -11, -12, -15, 09I, 11I, 12I, 15I,
09J, 11J, 12J and 15J.

The -09 ,09I and 09J speed grades are compliant to the DDR3-2133L (14-14-14) specification (The
09I industrial grade which is guaranteed to support -40°C

≤ T

CASE

≤ 95°C, the 09J industrial plus

grade which is guaranteed to support -40°C

≤ T

CASE

≤ 105°C).

The -11 ,11I and 11J speed grades are compliant to the DDR3L-1866 (13-13-13) specification (The
11I industrial grade which is guaranteed to support -40°C

≤ T

CASE

≤ 95°C, the 11J industrial plus

grade which is guaranteed to support -40°C

≤ T

CASE

≤ 105°C).

The -12, 12I and 12J speed grades are compliant to the DDR3L-1600 (11-11-11) specification (The
12I industrial grade which is guaranteed to support -40°C

≤ T

CASE

≤ 95°C, the 12J industrial plus

grade which is guaranteed to support -40°C

≤ T

CASE

≤ 105°C).

The -15, 15I and 15J speed grades are compliant to the DDR3L-1333 (9-9-9) specification (The 15I
industrial grade which is guaranteed to support -40°C

≤ T

CASE

≤ 95°C, the 15J industrial plus grade

which is guaranteed to support -40°C

≤ T

CASE

≤ 105°C).

The W632GU6NB  is  designed  to  comply  with  the  following  key  DDR3L  SDRAM  features  such  as
posted  CAS#,  programmable  CAS#  Write  Latency  (CWL),  ZQ  calibration,  on  die  termination  and
asynchronous reset. All of the control and address inputs are synchronized with a pair of externally
supplied differential clocks. Inputs are latched at the cross point of differential clocks (CK rising and
CK#  falling). All I/Os are synchronized with a differential DQS-DQS#  pair in a source synchronous
fashion.

2. FEATURES



Power Supply: 1.35V (typ.), V

DD

, V

DDQ

= 1.283V to 1.45V



Backward compatible to V

DD

, V

DDQ

= 1.5V ± 0.075V



Double Data Rate architecture: two data transfers per clock cycle



Eight internal banks for concurrent operation



8 bit prefetch architecture



CAS Latency: 5, 6, 7, 8, 9, 10, 11, 13 and 14



Burst length 8 (BL8) and burst chop 4 (BC4) modes: fixed via mode register (MRS) or selectable On-
The-Fly (OTF)



Programmable read burst ordering: interleaved or nibble sequential



Bi-directional, differential data strobes (DQS and DQS#) are transmitted / received with data



Edge-aligned with read data and center-aligned with write data



DLL aligns DQ and DQS transitions with clock



Differential clock inputs (CK and CK#)



Commands entered on each positive CK edge, data and data mask are referenced to both edges of
a differential data strobe pair (double data rate)



Posted CAS with programmable additive latency (AL = 0, CL - 1 and CL - 2) for improved command,
address and data bus efficiency



Read Latency = Additive Latency plus CAS Latency (RL = AL + CL)

«
...
3
4
5
6
7
...
»

Summary of Contents for W632GU6NB Series



































































































































































Reviews:

No comments

Related manuals for W632GU6NB Series

Brand: Campbell Pages: 32

grand Hard Disk

Brand: LaCie Pages: 2

Brand: Icy Box Pages: 36

Travelstar 14GS

Brand: IBM Pages: 2

Brand: E-Z-RECT Pages: 2

Barracuda 180 Family

Brand: Seagate Pages: 2

DDS Generation 6 USB

Brand: IBM Pages: 11

Brand: ABSCO SHEDS Pages: 21

HTS541680J9SA00 - Travelstar 80 GB Hard Drive

Brand: Hitachi Pages: 167

HTS541616J9AT00 - Travelstar 160 GB Hard Drive

Brand: Hitachi Pages: 2

HTS721010G9AT00

Brand: Hitachi Pages: 2

HTS541616J9AT00 - Travelstar 160 GB Hard Drive

Brand: Hitachi Pages: 188

HTS722010K9A300

Brand: Hitachi Pages: 2

MicroVault USM4GP

Brand: Sony Pages: 2

MicroVault USM64GQX

Brand: Sony Pages: 2

MicroVault USM4GN

Brand: Sony Pages: 2

MicroVault USM4GM

Brand: Sony Pages: 2

MicroVault USM4GL

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands