background image

Hardware Guide for miniVNA PRO2

 

 

 

 

 

+49 7276 / 96680         

www.wimo.com      [email protected]                     

 WiMo 2018

 

1

 

 

 
Congratulation ….

 

 
on your choice of miniRadioSolutions analyzer. 
This is the hardware reference manual. 

 
Safety 
 

Please carefully read the safety instruction included in this manual. 
 
The Software for 

miniVNA PRO2

 is continuously developed.  The current software is always downloadable from the internet. 

For the latest software and updates, visi

www.miniradiosolutions.com and http://vnaj.dl2sba.com/

 

 
 
The  new 

miniVNA  PRO2 

is  an  extraordinary  and  unique  hand-held  vector  network  analyzer  that  makes  available  a  multitude  of  new 

features and capabilities which are perfect for checking antennas and RF circuits for hams and commercial users. Together with your 
PC/Laptop, you can add to your laboratory the further advantages of having this first-class VNA instrument. 
 
This  is  the  first  world’s  wireless  analyzer  able  of  scanning  and  sending  the  data  using  an  integrated  Blue-tooth  module  to  a  remote 
PC/Notebook up to 100 meters from the 

miniVNA PRO2

’s location. This makes real-time antenna set-up easy!

 

 
 

 

 

 
 
 
 
 
 
 
 
Basic Carton Content 

 

 

  

 

 

      

                    

       

 

 
 

Hardware Guide

 

…………
………. 
…………. 

Specifications 

 

 

 

Frequency range 0.01-230 MHz  

 

Calibration using open-short-load for accurate results 

 

Range of Z from 1 to 1000 ohm 

 

Two ports VNA with S11 and S21; displayed and save results 

 

I/Q DDS Generator with output power of 0 dBm  

 

Two separate RF output I/Q for SDR experiment and IMD test with 
independent 0-55 dB attenuator; Phase adjustment resolution of 1 degree 

 

Built in Blue-tooth Class 1 for remote measurements 

 

Internal Battery Li-ion with 1000 mA/h (4 hours full- scan operation) 

 

Built-in battery charger (up to 400 mA)  

 

Accessory port for future optional interfaces and frequency extenders 

 

Low power consumption, 220 mA @ 3.7 V (analyzer mode using USB 
port) 

 

Power-saver mode 

 

SMA connectors for better isolation 

 

Extended dynamic range 

– up to 100dB in Transmission & 50 dB in 

Reflection 

 

Boot loader for future firmware upgrades 

 

User friendly interface for PC Windows, Linux and Mac 

 

Integrated Smith chart in software 

 

Optional extender for UHF and SHF band (under development) 

 

Mobile Phone software (under development) 

 

Measurements of motional crystal parameters, cable length, & more 

 

Export data in several formats 

– JPEG, EXCEL, ZPLOT, S2P, PDF 

 

Summary of Contents for miniVNA PRO2

Page 1: ...O2 s location This makes real time antenna set up easy Basic Carton Content Hardware Guide Specifications Frequency range 0 01 230 MHz Calibration using open short load for accurate results Range of Z from 1 to 1000 ohm Two ports VNA with S11 and S21 displayed and save results I Q DDS Generator with output power of 0 dBm Two separate RF output I Q for SDR experiment and IMD test with independent 0...

Page 2: ...s 2002 95 EC 2002 96 EC and 2003 108 EC relative to reduction of the use of hazardous substances in electrical and electronic equipment in addition to waste disposal The crossed bin symbol shown on the equipment indicates that at the end of its working life the product must be collected separately from other waste The user must therefore take the above equipment to the appropriate differentiated c...

Page 3: ...n the analyzer is set by the software interface to work in Reflection mode Caution Not apply to this port DC signals over 25 VDC and RF signals over 10 mW Voids Warranty DET Port is used to check filters and amplifiers when the analyzer is set by the software interface to work in Transmission mode Caution Not apply to this port DC signal over 25 VDC and RF signal over 10 mW Voids Warranty How to c...

Page 4: ... mode Run the pairing software from PC side and search for a new device Suggested option Calibration kit containing SMA open short 50 Ohm termination Part no 21010 SMA LED 6 LED 1 yellow Indicates battery in charge LED 2 green Indicates scan data LED 3 green Indicates power on LED 4 yellow Indicates flow of data LED 5 yellow Indicates flow of data LED 6 blue When flashing slow indicate the BT modu...

Reviews: