1
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
2
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
Installation Instructions for the Following Wilson
Electronics Signal Booster:
DB Pro™ Adjustable Gain In-Building Wireless
800/1900 MHz Smart Technology ™ Signal Booster
Model # 271265
FCC ID: PWO271265 IC: 4726A-271265
The term “IC” before the radio certification number only signifies that Industry Canada
technical specifications were met .
How it Works
Wilson Electronics Signal Boosters are bi-directional devices that deliver
service levels consistent with what would be expected in areas of high cell
network coverage . The Outside Antenna will collect the cell tower signal
and send it through the cable to the Signal Booster . The signal is then
boosted and sent to the Inside Antenna . Your cell phone or data card then
communicates with the improved signal . When the cellular device transmits,
the signal goes through the Inside Antenna, is boosted by the Signal Booster
and transmitted to the cell tower through the Outside Antenna .
Inside this Package
DB Pro™
Signal Booster
AC/DC Power Supply
Accessories & Antenna Options
(may be included in some kits)
To purchase call Wilson Electronics Sales Department at: 800-204-4104
1 . 1900 MHz Yagi PCS Antenna (301124)*
2 . 800 MHz Yagi Cellular Antenna (301129)*
3 . 800/1900 MHz Omni-Directional Antenna
75 Ohm (301201)
4 . 700-2700 MHz Wide Band Directional Antenna (304475)
5 . 700-2700 MHz Wide Band Panel Antenna (301155)
6 . Lightning Surge Protector 75 Ohm (859988)
Splitters options on page 8
Select a location to install the Signal Booster that is away from
1 .
excessive heat, direct sunlight, moisture and has proper ventilation .
Do not place the Signal Booster in an air-tight enclosure .
Select a location on the roof of the building to install the Outside
2 .
Antenna . Use a cell phone in test mode to find the strongest signal from
the cell tower . Visit
www.WilsonElectronics.com
to find test mode function
for your particular cell phone or see page 7 .
Run the Outside Antenna cable to the Signal Booster and attach it to
3 .
the connector labeled “Outside Antenna” on the Signal Booster . Run
the Inside Antenna cable to the Signal Booster and attach it to the
connector labeled “Inside Antenna” on the Signal Booster (see page
7 for more information on running cable) . Lightning Surge Protection
is recommended for all in-building installations (see page 6) .
Select a location for the Inside Antenna, preferably in the center of
4 .
where the signal needs to be amplified (see page 8) . A minimum
separation distance of 20
vertical
feet is necessary for operation . If
the inside coverage is not sufficient you may need as much as 75 feet
of
horizontal
separation . See installation diagram on pages 3 & 4 .
Before powering up the Signal Booster, verify that both the Outside
5 .
Antenna and the Inside Antenna are connected and check that
all connections are tight (see page 9) .
Note: Be careful when
plugging the connectors in so as not to bend the center pins on the
connectors.
The Signal Booster has been packaged with the gain control knobs
6 .
adjusted to the highest gain position . If one or both of the lights are
not green please refer to pages 10 &11 .
Quick Install Overview
See Installation Diagram on pages 3 & 4 . Contact Wilson Electronics
Technical Support Team with any questions at 866-294-1660 .
3
1
2
5
6
4
*Requires N-Male to F-Female adapter/converter (971128)
Appearance of device and accessories may vary .
Warning:
Connecting the Signal Booster directly to a cell phone with
use of an adapter will damage the cell phone and/or the
Signal Booster .
Wilson
®
Electronics recommends that all AC power
supplies for home electronics be plugged into a
Surge Protector Power Strip.
