Wilo Wilo-Drain SP, Installation And Operating Instructions Manual

Page: 37 / 52

ENGLISH
11
Direction of rotation must correspond to the arrow attached or
engraved in the pump.
Check direction of rotation when motor is apart (coupling spacer
dismantled or motor not coupled to pump). If not feasible due to pump
design (pump fitted with rigid coupling) it is necessary to check that
pump shaft turns freely after the test and before final pump start.
To check direction of rotation start motor briefly and check direction of
rotation just before rotation stops. If direction of rotation must be
modified then reverse two phases in motor junction box.
It is possible to change two phases in the control cabinet on motor
starter connections. If this solution is preferred then it will be
necessary to modify the identification of the cables in the electrical
drawings too.
5.2.4 NOISE LEVEL
Noise level of a complete pump set depends on motor type and speed,
on quality and wear of flexible coupling (if concerned), on fluid velocity,
piping design, … Values given hereafter are only indicative and based on
fan cooled electric motors average noise levels.
The test must be performed on the supplied pump if the noise
level must be certified.
If noise level is higher than 85dBA, personel working in pump area
should wear hearing protections.
Pump size
Speed
(RPM)
For
maximum
flow [dB]
At best
efficiency oint
[dB]
At zero flow
[dB]
40 2900 71 66 79
41 2900 66 62 73
45 2900 71 68 69
46 2900 66 65 68
50 2900 75 69 72
51 2900 68 66 69
60 2900 72 71 73
61 2900 67 67 74
63 S2900 85 79 80
65 1450 64 62 68
68 2900 87 79 83
80(-2) 2900 85 72 74
80K 2900 79 73 76
83 2900 89 78 86
85 1450 68 65 72
88 2900 94 87 89
88(210) 2900 90 83 84
100 2900 88 81 98
105 1450 83 67 73
108 2900 86 84 84
120 1450 78 74 78
150 1450 84 74 89
160 1450 81 75 80
170 950 83 76 77
Indicative noise level given in dBA (LpA at 1 m)
5.2.5 CONNECTIONS

Suction flange axis is horizontal and the face is vertical.

Discharge flange axis is vertical and the face is horizontal.
5.2.6 PERMISSIBLE FORCES A ND MOMENTS
No other stress than the one due to fastening of pipe and pump
flanges together should apply. No stress must be applied to pump
casing by the pipe work. A pre-stress may exceptionally be applied to
flanges to compensate a pipe expansion. But in any case the resulting
forces should not exceed values given hereafter :
DN
F
(x, y, z)
(N)
M
t (x, y, z)
(Nm)
1’’1/2 - 40 415 208
2’’ - 50 520 264
3’’ - 80 520 264
4’’ - 100 832 416
6’’ - 150 1040 528
8’’ - 200 1220 670
Applied forces and moments should not be maximum at the same
time.
5.2.7 SCOPE OF DELIVERY
Pump can be delivered as a complete pump set including electrical
motor, flexible coupling, coupling guard and baseplate. It can be also
delivered without one of those parts. A CE integration certificate is then
supplied.
This instructions and operating manual is part of the pump supply and
should be delivered attached to the pump. If not, ask WILO Customer
department to get it.
ATEX pumps may be delivered with specific instrumentation. Refer
to pump technical datasheet or to acknowledgment of order to
know exhaustive scope of supply.
6 DESCRIPTION AND WORKING PRINCIPLE
6.1 PRODUCT INFORMATION
S pump is a single stage self priming pump. Several variants of
construction are available : close-coupled (without shaft coupling),
Biblock or with ball bearings assembly fitted with elastic coupling.
Close-coupled pumps use a long shaft electric motor. Biblock pumps
accept flanged normalized IEC motor. Other pumps sets use IEC B3
motors. Diesel or gasoline engines can be used for mobile or fixed
installations.
S pumps include an open impeller, wear plate(s) (rear and front wear
plates according to pump size), single mechanical seal and non-return
valve integrated in the suction flange assembly.
Zinc anodes or internal coating with Ceram C0 can be supplied as an
option for specific applications.
[A] Suction flange with integrated non-return valve.
[B] Priming chamber.
[C] Inspection cover.
[D] Drain cover or plug (depending on pump size).
[E] Wear plate(s).
[F] Open impeller.
[G] Lifetime lubricated ballbearings.
[H] Shaft.
[I] Mechanical seal.
[J] Air / liquid separation chamber.
[K] Discharge flange assembly.