background image

English

Installation and operating instructions Wilo-SiFire System

31

3.1 Residual risk during transport and storage

WARNING! Risk of Cut!
Sharp edges or any not protected threaded parts 
entail the risk of getting cut.
Take necessary cautions to avoid injuries and 
use protective equipment (wear specific 
gloves).

WARNING! Risk of personal injury!

 

Do not stand or put members under the sus-
pended parts during handling and installation. 
Use clothing dedicated to protection against 
accidents (wear helmet and safety shoes).

 

WARNING! Risk of impact!
Be careful of prominent parts and parts at head 
level. Use clothing dedicated to protection 
against accidents.

DANGER! Risk of fall!
Prohibit access to wells or tanks, where pumps 
are installed. Wells must have closing cover.

WARNING! Risk of irritation!
During handling, avoid spillage of battery acid 
solution which could cause irritations or mate-
rial damages. Use special protections to avoid 
contact.

CAUTION! Risk of environmental pollution!
Avoid dumping of oil from the engine or diesel 
fuel from the tank. During handling, keep them 
flat. Use suitable protection and implement the 
necessary measures to prevent pollution of soil, 
water, etc.

4 Intended use

The fire extinguishing boosters are designed for a 
professional use. They are used when an increase 
or a maintaining under pressure of the fire net-
work is necessary. 

The system must be installed in a special room 
which is protected from frost and rain, fireproof 
and ventilated enough, with necessary spaces 
around pumps for movements and regular main-
tenance .The room must be in accordance with the 
EN 12845 standards. Airflow for ventilation and 
for cooling of engines, more specifically diesel 
engine -if present- has to be sufficient.

5 Product data

5.1 Type key   

   

Example

SiFire EN 40-200

 

180 7,5/10.5/0.55 EDJ

SiFire

Name of the Fire Extinguishing System

EN

In accordance with EN 12845 standards

40/200

Type of main pump

180

Impeller diameter of main pump

7,5/10.5/
0.55

Nominal power of the pump motors [kW]
(electrical motor/diesel engine/jockey motor)

EDJ

Configuration:
E

: 1 electric pump

D

: 1 diesel pump

EJ : 1 electric pump + 1 jockey pump 
EEJ : 2 electric pumps + 1 jockey pump
EDJ : 1 electric pump + 1 diesel pump + 1 jockey 

pump

DJ : 1 diesel pump + 1 jockey pump

5.2

Technical data

Maximum operating pressure:

10 bar/16 bar according to the pump

Maximum ambient temperature:

+4 to +40 °C (10 to 40°C if diesel pump is installed)

Maximum water temperature:

+4 to +40 °C

Supply voltage:

3~400 V ± 10 % 
(1~230 V ± 10 %, for diesel pump control panel)

Frequency:

50 Hz

Maximum relative humidity:

50 % with Tmax.: 40 °C (*)

Protection class of Control box:

IP54

Protection class of pump:

IP54

Motor IE2 insulation class:

F

Maximum altitude for installation:

1000 m above sea level (*)

Minimum atmospheric pressure:

760 mmHg (*)

Nominal current:

refer to the rating plate

(*) Seen the specific graphs and tables in the catalogues and maintenance manuals for the details of class variations for electric machines and diesel engines with 

regard to different temperatures, altitudes, atmospheric pressure, fuel temperature and viscosity compared to standard test conditions.

Summary of Contents for SiFire







































Reviews: