background image

 

 

Owner’s Manual                                

Save this manual for future reference.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 
 
 
 
 
 

Electric Counterflow 
Wall Heater 

 

Model Number:  
3144030 

READ THIS OWNER’S MANUAL CAREFULLY BEFORE YOU 
INSTALL YOUR NEW WILLIAMS WALL HEATER. 

 
 
 
 
 

–  Do not store or use gasoline or other 

flammable vapors and liquids in the vicinity of 
this or any other appliance. 

 

–  If you smell smoke

Danger of electrical shock 

   

•  Do not touch heater. 

   

•  Immediately shutdown main electrical 

supply to heater. 

   

•  Extinguish any open flame. 

   

•  Contact a qualified installer or service 

agency. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The Manufacturer, Williams Heater Co., warrants this wall heater or heater to the original purchaser under the following conditions: 

LIMITED ONE-YEAR WARRANTY 

Williams Furnace Co.   

   250 West Laurel Street   

   Colton, California 92324 U.S.A. 

WARNING: 

 Failure to comply with 

instructions could result in personal injury, 
property damage and/or death. 

 

Summary of Contents for 3144030





















Reviews: