Wilden Original PX15, Operation & Maintenance Manual

Page: 4 / 39

WILDEN PUMP & ENGINEERING, LLC 2
WIL-10330-E-04
PX15 METAL
76 mm (3") Pump
Maximum Flow Rate:
918 lpm (243 gpm)
LEGEND
PX15 / XXXXX / XXX / XX / X XX /
XXXX
O-RINGS
MODEL
VALVE SEAT
VALVE BALLS
DIAPHRAGMS
AIR VALVE
CENTER BLOCK
AIR CHAMBERS
WETTED PARTS & OUTER PISTON
SPECIALTY
CODE
(if applicable)
MATERIAL CODES
MODEL
PX15 = 76 MM (3")
XPX15 = 76 MM (3") ATEX
WETTED PARTS/OUTER
PISTON
1
AA = ALUMINUM /
ALUMINUM
SS = STAINLESS STEEL /
STAINLESS STEEL
WW = DUCTILE IRON /
DUCTILE IRON
AIR CHAMBERS
A = ALUMINUM
S = 316 STAINLESS STEEL
CENTER BLOCK
A = ALUMINUM
S = 316 STAINLESS STEEL
P = POLYPROPYLENE
AIR VALVE
A = ALUMINUM
S = 316 STAINLESS STEEL
P = POLYPROPYLENE
DIAPHRAGMS
BNS = BUNA-N (Red Dot)
XBS = CONDUCTIVE BUNA-N
(Two Red Dots) 2
EPS = EPDM (Blue Dot) 2
PUS = POLYURETHANE (Clear)
NES = NEOPRENE (Green Dot)
TEU = PTFE
w/EPDM
BACK-UP (white) 2
TNU = PTFE w/NEOPRENE
BACK-UP (White)
FSS = SANIFLEX™ [Hytrel ®
(Cream)]
VTS = VITON ® (White Dot)
WFS = WIL-FLEX™ [Santoprene ®
(Orange Dot)]
TSU = PTFE W/SANIFLEX™
BACK-UP (White)
BNU = BUNA-N, ULTRA-FLEX™
EPU = EPDM,
ULTRA-FLEX™ 2
NEU = NEOPRENE,
ULTRA-FLEX™
VTU = VITON ® , ULTRA-FLEX™
TSS = FULL STROKE PTFE
W/SANIFLEX™ BACK-UP
TWS = FULL STROKE PTFE
W/WIL-FLEX™ BACK-UP
VALVE BALL
BN = BUNA-N (Red Dot)
FS = SANIFLEX™
[Hytrel
® (Cream)]
EP = EPDM (Blue Dot) 2
NE = NEOPRENE (Green Dot)
PU = POLYURETHANE (Brown)
TF = PTFE (White)
2
VT = VITON ® (Silver or White Dot)
WF = WIL-FLEX™ [Santoprene ®
(Orange Dot)]
VALVE SEAT
A = ALUMINUM
BN = BUNA-N (Red Dot)
EP = EPDM (Blue Dot)
2
FS = SANIFLEX™ [Hytrel ®
(Cream)]
NE = NEOPRENE (Green Dot)
PU = POLYURETHANE (Brown)
VT = VITON
® (Silver or White
Dot)
WF = WIL-FLEX™ [Santoprene
®
(Orange Dot)]
M = MILD STEEL
S = STAINLESS STEEL
VALVE SEAT O-RING
TF = PTFE (White) 2
SPECIALTY CODES
0014 BSPT
0022 External SS fasteners
0044 Stallion balls & seats only
0070 SaniFlo
™
FDA
0079 Tri-clamp ™ fittings, wing nuts
0080 Tri-clamp
™
fittings, ONLY
0100 Wil-Gard II ™ 110V
0102 Wil-Gard II ™ sensor wires ONLY
0103 Wil-Gard II
™
220V
0118 Stallion balls & seats only, BSPT0120
Saniflo ™ FDA, Wil-Gard II ™ 110V
0319 Single-Point Exhaust center block, BSPT
0320 Single-Point Exhaust center block
0324 Single-Point Exhaust center block,
Screen based
0327 Single-Point Exhaust center block,
Stallion externals, balls & seats
0341 Single-Point Exhaust center block,
SaniFlo ™ FDA
NOTE: MOST ELASTOMERIC MATERIALS USE COLORED DOTS FOR IDENTIFICATION.
NOTE: Not all models are available with all materials options.
Viton
®
is a registered trademark of DuPont Dow Elastomers.
NOTE:
1. PTFE-fitted models require stainless steel outer piston.
2. Meets the requirements of ATEX.
S e c t i o n 2
W I L D E N P U M P D E S I G N A T I O N S Y S T E M