background image

WIL-10330-E-04

 

19 

WILDEN PUMP & ENGINEERING, LLC

T o o l s   R e q u i r e d :

•  

11/16" Wrench

•  

3/4" Wrench

•  

Adjustable Wrench

•  

Vise equipped w/
soft jaws (such as 
plywood, plastic 
or other suitable 
material)

CAUTION: 

Before any maintenance or repair is attempted, the compressed air line 

to the pump should be disconnected and all air pressure allowed to bleed from the 
pump. Disconnect all intake, discharge, and air lines. Drain the pump by turning it 
upside down and allowing any fl uid to fl ow into a suitable container. Be aware of 
any hazardous effects of contact with your process fl uid.

NOTE:

 The model photographed for these instructions incorporates rubber 

diaphragms, balls, and seats. Models with PTFE diaphragms, balls and seats are 
the same except where noted. 

Step 1.

Before starting disassembly, mark 
a line from each liquid chamber to 
its corresponding air chamber. This 
line will assist in proper alignment 
during reassembly. 

Step 2

Utilizing a 11/16" wrench, remove 
the two small clamp bands that 
fasten the discharge manifold to 
the liquid chambers.

Step 3

Remove the discharge manifold to 
expose the valve balls and seats. 
Inspect  ball  cage  area  of  manifold 
for excessive wear or damage. 

S e c t i o n   7

P U M P   D I S A S S E M B L Y

Summary of Contents for Original PX15








































Reviews: