background image

 

 

 

2. 

 Technical data 

2.1 

 General technical data 

  

 

1

 The back-tilt moment has been calculated at 18 Mpa (180 bar) working pressure. 

2

 Four positions from inside fork to centre of rotating shaft. 

 

Model 

Letter  Description 

 

 

 

K55A/K55C/SK55A/SK55C 

Rotating to the left 

 

Rotating to the right 

 

 

 

SK55A/SK55C 

Electrically controlled reversing valve 

 

4-hose connection 

Table 2.1.2- Description data on model plate

  

 

Model 

K55A 

K55C 

SK55A 

SK55C 

Max. carrying capacity 

2500 kg 

2500 kg 

3500 kg 

3500 kg 

Weight 

295 kg

 

370 kg

 

370 kg 

450kg 

Max. working pressure 

22Mpa (220 bar) 

22Mpa (220 bar) 

22Mpa (220 bar) 

22Mpa (220 bar) 

Back-tilt moment  

1

 

10,8 KNm 

10,8 KNm 

10,8 KNm 

10,8 KNm 

Center of gravity 

156 mm

 

156 mm 

132 mm 

138 mm 

Frontal extension length 

173 mm 

193 mm  

173 mm 

193 mm 

Height of the fork carrier 

407 mm (FEM II) 

407 mm (FEM II) 

508 mm (FEM III) 

508 mm (FEM III) 

Rotation angle 

180° 

180° 

180° 

180° 

Fork carrier width 

1070 mm 

1070 mm 

1070 mm 

1070 mm 

Side-shift 

Nee 

Nee 

Ja 

Ja 

Third fork foldaway 

580/700/800/900mm  580/700/800/900mm  580/700/800/900mm  580/700/800/900mm 

Tabel 2.1.1-Uitvoeringen WIFO kistenkantelaar 

Summary of Contents for K55A

























Reviews: