background image

Terra Clean 100

 

5  Assembly 

 

 

 

28 

239 99 01 

 003 

10 | 2020 

 

4.4.

 

Operating materials 

Designation 

Specifications 

Lubricating greases 

MT47 (visc. 55) 
Min. 3%

5% molybdenum sulphide 

5.

 

Assembly 

5.1.

 

General information on assembly 

 

DANGER!

 

An unsecured tractor poses a risk of injury. 

 

Switch the machine and the motor of the tractor off and remove the ignition key before carrying out 
maintenance. 

 

Secure the tractor to prevent it from rolling away. (parking brake). 

 

Always position the machine on a flat surface before detaching it. 

 

 

WARNING!

 

Failure to wear personal protective equipment poses a risk of injury. 

 

Wear personal protective equipment. 
See Section 3.6.10 

Personal protective equipment

 

5.2.

 

Unpacking the machine 

The transport frame is made up of the following 
components: 

 

Lower section  (

1

 

Front section  (

2

 

Rear wall  (

3

 

Top part  (

4

 

Individual bars on the left and right 

 

Remove the top part (

4

)  

and side walls  

(

5

).  

 

Lay the front section  (

2

)  on the lower section  (

1

)  as a 

ramp.  

 

Remove the bolt  (

6

)  and squared timber  (

7

). 

 

 

Attach the drawbar (see chapter 5.3 

Installing the 

drawbar). 

 

Set the machine to the transport position (see chapter 
7.3 

 Support for drawbar

 

Pull the machine down the ramp from the lower section 
or lift it off using a crane (see chapter 6.2.2 

Transport 

Using a Crane

). 

Summary of Contents for Terra Clean 100




















































Reviews: