background image

1

W10443045B

W10443046B-SP

Table of Contents 

DRYER SAFETY ................................................................

2

 

INSTALLATION REQUIREMENTS ....................................

4

 

 

Tools and Parts .................................................................... 4

 

 

Location Requirements ...................................................... 5 

 

Electric Dryer Power Hookup-Canada Only ..................... 7

 

Gas Dryer Power Hookup ................................................... 8

VENTING .................................................................................... 10

 

 

Venting Requirements ....................................................... 10

 

Plan Vent System ............................................................... 11

 

 

Install Vent System ............................................................ 12

INSTALL LEVELING LEGS ........................................................ 12

MAKE GAS CONNECTION ....................................................... 13

 

CONNECT INLET HOSES ......................................................... 13

CONNECT VENT ....................................................................... 15

LEVEL DRYER ........................................................................... 15

COMPLETE INSTALLATION CHECKLIST ............................... 16

 

DOOR REVERSAL ..................................................................... 16

STACKING WASHER AND DRYER .......................................... 16  

TROUBLESHOOTING ............................................................... 16

INSTALLATION NOTES

Date of purchase:

 _________________________________

Date of installation:

 _______________________________

Installer:

 ________________________________________

Model number:

 ___________________________________

Serial number:

 ___________________________________

Date d’achat :

 _____________________________________

Date d’installation :

 ________________________________

Installateur :

 ______________________________________

Numéro de modèle :

 ________________________________

Numéro de série :

 __________________________________

NOTES CONCERNANT L’INSTALLATION

Table des matières

SÉCURITÉ DE LA SÉCHEUSE .......................................

17

 

EXIGENCES D’INSTALLATION ......................................

19

 

 

Outillage et pièces ............................................................ 19

 

 

Exigences d’emplacement ............................................... 20

 

Raccordement à l’alimentation électrique de  

 

la sécheuse électrique – Canada seulement .................. 22

 

Raccordement d’une sécheuse à gaz ............................. 23

L’ÉVACUATION.......................................................................... 25

 

 

Exigences concernant l’évacuation ................................ 25

 

 

Planification du système d’évacuation ........................... 26

 

 

Installation du circuit d’évacuation ................................. 28

 

INSTALLATION DES PIEDS DE NIVELLEMENT ..................... 28 

RACCORDEMENT AU GAZ ...................................................... 29

RACCORDEMENT DU TUYAU D’ARIVÉE D’EAU ................... 29

RACCORDEMENT DU CONDUIT D’ÉVACUATION ................ 31

RÉGLAGE DE L’APLOMB DE LA SÉCHEUSE......................... 31

ACHEVER L’INSTALLATION – LISTE DE VÉRIFICATION ....... 32

 

INVERSION DE LA PORTE ....................................................... 32

LAVEUSE ET SÉCHEUSE SUPERPOSÉES ............................. 32  

DÉPANNAGE ............................................................................. 32

Gas Dryer Installation Instructions 

Canadian Electric Dryer Installation Instructions 

Instructions pour l’installation de la sécheuse à gaz  

(É.-U. et Canada) et électrique (Canada uniquement) 

Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su 

producto, visite:  

www.whirlpool.com 

Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad 

superior de la puerta.

Summary of Contents for YWED9050XW

















Reviews: