Whirlpool WSE 2930 W Manual Download Page 46

Page: 46 / 101

Functional characteristics

NTC sensor failure management

Freezer Compartment:

The following emergency procedure must be performed if the freezer temperature sensor became

unreliable:

Compressor, Compressor fan (1 minute delay since compressor starting) and Evaporator fan (3 minutes

delay since compressor starting) will be driven constantly till the emergency will recover.

No change will be implemented for refrigerator compartment algorithm and defrost operation.

The freezer probe is defect, if the resistance value is higher than 110 Kohm or lower than 500 ohm.

Refrigerator Compartment:

The following emergency procedure must be performed if the Refrigerator temperature sensor became

unreliable:

Damper and Evaporator fan shall cycle 15 minutes ON (Damper open and Evaporator run) and 30 minutes

OFF constantly till the emergency will recover.

Summary of Contents for WSE 2930 W






































































































Search results

Summary of Contents for WSE 2930 W

Reviews:

Related manuals for WSE 2930 W

Brands by name

Popular brands

Whirlpool WSE 2930 W, Manual

Search results

Summary of Contents for WSE 2930 W

Reviews:

Related manuals for WSE 2930 W

Brands by name

Popular brands