manualshive.com logo in svg

Whirlpool WRS315SDHM, Owner'S Manual

Share
Download
Whirlpool WRS315SDHM Owner'S Manual Download Page 28

28

Water Filtration System

Model P8WB2L (EDR1RXD1, Filter 1) Capacity 200 Gallons (757 Liters)

System tested and certified by NSF International against NSF/
ANSI Standard 42, 53, 401 and CSA B483.1 for the reduction of
contaminants specified on the Performance Data Sheet.

This system has been tested according to NSF/ANSI Standards 42, 53, 401 and CSA 483.1** for the reduction of the substances listed
below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to
the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42, 53, 401 and CSA 483.1**

**Certified to CSA B483.1 only for use in Refrigerator applications.

Substance Reduction

Aesthetic Effects

Influent Challenge

Concentration

Maximum Permissible

Product Water Concentration

Average % Reduction

Chlorine Taste/Odor

Particulate Class I*

2.0 mg/L ± 10%

At least 10,000 particles/mL

50% reduction

85% reduction

97.2%

99.9%

Contaminant Reduction

Influent Challenge

Concentration

Maximum Permissible

Product Water Concentration

Average % Reduction

Lead***: @ pH 6.5 / @ pH 8.5

0.15 mg/L ± 10%

0.010 mg/L

96.0%

Benzene

0.015 mg/L ± 10%

0.005 mg/L

99.8%

P-Dichlorobenzene

0.225 mg/L ± 10%

0.075 mg/L

91.9%

Carbofuran

0.08 mg/L ± 10%

0.040 mg/L

92.4%

Toxaphene

0.015 ± 10%

0.003 mg/L

>99%

Atrazine

0.009 mg/L ± 10%

0.003 mg/L

>99.99%

Asbestos

10

7

to 10

8

fibers/L††

99%

99.0%

Live Cysts†

50,000/L min.

99.95%

>96.6%

Turbidity

11 NTU ± 10%

0.5 NTU

>99.8%

Lindane

0.002 ± 10%

0.0002 mg/L

99.40%

Tetrachloroethylene

0.015 mg/L ± 10%

0.005 mg/L

>99.8%

o-Dichlorobenzene

1.8 mg/L ± 10%

0.60 mg/L

93.8%

Ethylbenzene

2.1 mg/L ± 10%

0.70 mg/L

99.8%

1,2,4-Trichlorobenzene

0.210 mg/L ± 10%

0.07 mg/L

87.9%

2,4 - D

0.210 mg/L ± 10%

0.07 mg/L

>96.6%

Styrene

2.0 mg/L ± 10%

0.1 mg/L

95.9%

Toluene

3.0 mg/L ± 10%

1.0 mg/L

>96.9%

Endrin

0.006 mg/L ± 10%

0.002 mg/L

>96.4%

Atenolol

200 ± 20%

60 ng/L

>97.0%

Trimethoprim

140 ± 20%

20 ng/L

>97.4%

Linuron

140 ± 20%

20 ng/L

>97.9%

Estrone

140 ± 20%

20 ng/L

93.8%

PERFORMANCE DATA SHEET

Summary of Contents for WRS315SDHM






























Reviews:

No comments

Brands by name

Popular brands

Load more brands