manualshive.com logo in svg

Whirlpool WRS315SDHM, Owner'S Manual

Share
Download
Whirlpool WRS315SDHM Owner'S Manual Download Page 20

20

10.

Close the freezer door and use a TORX T30 screwdriver to
remove the top hinge completely as shown below.

A. Do not remove screws.

IMPORTANT:

Do not remove either screw A. Hold the door

while hinge is being removed.

11.

.Lift the refrigerator door straight up off from the bottom hinge
as shown below.

IMPORTANT:

Rest the door on its side on a soft, clean

surface, such as a towel, blanket, or piece of cardboard. This
will help to avoid scratching or damaging the door.

12.

If your refrigerator without doors does not pass through the
doorway, you may remove both bottom hinges. Use a 5/16"
nut driver to remove these as shown below..

B. Do not remove B screws

IMPORTANT:

Do not remove either screw B.

Replace Doors and Hinges

If your doors and bottom hinges have been removed, please
follow the next instructions for reinstallation:

1.

Reinstall both bottom hinges using a 5/16" nut driver to tighten
screws as shown below.

B. Do not remove B screws

2.

If your model has water dispensing in the door:

�

Lift the freezer door enough to feed the water dispenser
tubing and wiring through the bottom hinge pin as shown
below.

NOTE:

This may require two people, one to lift the door

and the other to feed the water tubing and wiring into the
bottom hinge pin.

IMPORTANT:

Hold the door while hinge is being installed.

3.

Close the freezer door to align and reinstall the top hinge. Use
a TORX T30 screwdriver to tighten the screws as shown
below.

A. Do not remove A screws

IMPORTANT:

Provide additional support for the door while top

hinge is being reinstalled. Do not depend on the door magnets
to secure the door to the cabinet.

Summary of Contents for WRS315SDHM






























Reviews:

No comments

Brands by name

Popular brands

Load more brands