background image

15

 

Do not store anything on top of the ice maker or in the ice 

storage bin.

Water Dispenser

IMPORTANT:

 

After connecting the refrigerator to a water source or 

replacing the water filter, flush the water system. Use a 

sturdy container to depress and hold the water dispenser 

lever for 5 seconds, then release it for 5 seconds. Repeat 

until water begins to flow. Once water begins to flow, 

continue depressing and releasing the dispenser lever (5 

seconds on, 5 seconds off) until a total of 4 gal. (15 L) has 

been dispensed. This will flush air from the filter and water 

dispensing system, and prepare the water filter for use. 

Additional flushing may be required in some households. As 

air is cleared from the system, water may spurt out of the 

dispenser.

NOTE:

 After 5 minutes of continuous dispensing, the 

dispenser will stop dispensing water to avoid flooding. To 

continue dispensing, press the dispenser button again.

 

Allow 24 hours for the refrigerator to cool down and chill 

water. Dispense enough water every week to maintain a fresh 

supply.

Dispensing Water

1. 

Hold a container under the dispenser while pressing the 

button.

2. 

Release the button to stop dispensing.

Water Filtration System

The water filter is located in the upper right-hand corner of the 

refrigerator compartment.

IMPORTANT:

 The disposable water filter should be replaced at 

least every 6 months. If the water flow to the water dispenser or 

ice maker decreases noticeably before 6 months have passed, 

replace the water filter more often.

Replacing the Water Filter

To purchase replacement water filters, model UKF8001AXX-750 

or model UKF8001AXX-200, contact your dealer or call  

1-800-253-1301

 U.S.A. or 

1-800-807-6777

 Canada.

IMPORTANT:

 Air trapped in the water system may cause water 

and filter to eject. Always dispense water for at least 2 minutes 

before removing the filter or blue bypass cap.

1. 

Turn filter counterclockwise to remove.

2. 

Remove sealing label from replacement filter and insert the 

filter end into the filter head.

3. 

Turn the filter clockwise until it stops. Snap the filter cover 

closed.

4. 

Flush the water system. See “Water and Ice Dispenser(s).”

NOTE:

 The dispenser feature may be used without a water filter 

installed. Your water will not be filtered. If this option is chosen, 

replace the filter with the blue bypass cap.

REFRIGERATOR CARE

Cleaning

Both the refrigerator and freezer sections defrost automatically. 

However, clean both sections about once a month to avoid 

buildup of odors. Wipe up spills immediately.

IMPORTANT:

 

Because air circulates between both sections, any odors 

formed in one section will transfer to the other. You must 

thoroughly clean both sections to eliminate odors. To avoid 

odor transfer and drying out of food, wrap or cover foods 

tightly.

 

For stainless steel models, stainless steel is corrosion-

resistant and not corrosion-proof. To help avoid corrosion of 

your stainless steel, keep your surfaces clean by using the 

following cleaning instructions.

To Clean Your Refrigerator:

NOTE:

 Do not use abrasive or harsh cleaners such as window 

sprays, scouring cleansers, flammable fluids, muriatic acid, 

cleaning waxes, concentrated detergents, bleaches or cleansers 

containing petroleum products on exterior surfaces (doors and 

cabinet), plastic parts, interior and door liners or gaskets. Do not 

use paper towels, scouring pads, or other harsh cleaning tools.

1. 

Unplug refrigerator or disconnect power.

2. 

Hand wash, rinse, and dry removable parts and interior 

surfaces thoroughly. Use a clean sponge or soft cloth and a 

mild detergent in warm water.

Do not use with water that is microbiologically unsafe or 

of unknown quality without adequate disinfection before 

or after the system. Systems certified for cyst reduction 

may be used on disinfected waters that may contain 

filterable cysts.

WARNING

Explosion Hazard

Use non-flammable cleaner.
Failure to do so can result in death, explosion, or fire.

Summary of Contents for WRB322DMBW00
























Reviews: