Whirlpool M-17 Technical Manual Download Page 74

Page: 74 / 88

COMPONENT ACCESS (Cont.)

4-10

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Removing the Upper Rack

(for SatinGlide rails)

Open the dishwasher door.

To gain access to the removable tabs on the tracks/rails, pull

the upper rack forward about halfway out of the tube.

On one side, press the tab on the track in and pull up the

front end of the rack out of the track.

Then repeat this step on the other side to completely remove

the front end of the rack.

Then remove the back end of the rack, by pulling the back

end out with a slightly forward, and then upward motion.

Remove Roller and Rack Adjuster

Assembly

Remove rack adjust retainer. Using a flat blade screwdriver

push in on the tab.

While pushing in on tab lift up on the rack adjust retainer to

remove.

Repeat for other rack adjust tab.

Using a flat blade screwdriver push in on two tabs as shown

in below image:

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands