background image

INSTALLATION INSTRUCTIONS

30" (76 CM) FREESTANDING ELECTRIC RANGES

Table of Contents

RANGE SAFETY ................................................................................... 2

INSTALLATION REQUIREMENTS ...................................................... 3

Tools and Parts .................................................................................. 3
Location Requirements ...................................................................... 3
Electrical Requirements - U.S.A. Only ............................................... 4

INSTALLATION INSTRUCTIONS ........................................................ 6

Unpack Range.................................................................................... 6
Install Anti-Tip Bracket ....................................................................... 6
Electrical Connection - U.S.A. Only ................................................... 7
Verify Anti-Tip Bracket Location ...................................................... 12
Level Range...................................................................................... 12
Storage Drawer ................................................................................ 12
Complete Installation ....................................................................... 13
Moving the Range ............................................................................ 14

ANTI-TIP BRACKET TEMPLATE  ..................................................... 15

IMPORTANT:

 

Save for local electrical inspector's use.

W10252706B

Summary of Contents for GFE461LVT

















Reviews: