background image

WASHER INSTALLATION INSTRUCTIONS

WASHER SAFETY

Table of Contents

WASHER SAFETY............................................ 1

INSTALLATION REQUIREMENTS ................. 2

Tools and Parts ............................................. 2
Location Requirements................................. 3
Drain System................................................. 3
Electrical Requirements ................................ 4

INSTALLATION INSTRUCTIONS ................... 4

Before You Start............................................ 4
Remove Shipping Strap................................ 4
Connect Drain Hose...................................... 5
Connect the Inlet Hoses ............................... 5
Secure the Drain Hose .................................. 7
Level the Washer........................................... 7
Complete Installation .................................... 8

You can be killed or seriously injured if you don't immediately 
 

You

 

can be killed or seriously injured if you don't follow 

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety 
messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

8316566

Summary of Contents for 8316566









Reviews: