Whirlpool 7MWFC6820LC Owner'S Manual Download Page 3

3

ALL-IN-ONE WASHER & DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These
words mean:

DANGER

You can be killed or seriously injured if you don't
immediately follow instructions.

WARNING

You can be killed or seriously injured if you don’t follow
instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions,

including the following:

Read all instructions before using the appliance.

Do not wash or dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, or other flammable or explosive
substances, as they give off vapors that could ignite or
explode.

Do not add gasoline, dry-cleaning solvents, or other
flammable or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.

Under certain conditions, hydrogen gas may be produced
in a hot-water system that has not been used for 2 weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If the hot-water
system has not been used for such a period, before using a
washing machine, turn on all hot-water faucets and let the
water flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is flammable,
do not smoke or use an open flame during this time.

Do not allow children to play on or in the appliance. Close
supervision of children is necessary when the appliance is
used near children.

Before the appliance is removed from service or discarded,
remove the door.

Do not reach into the appliance if the tub is moving.

Do not install or store this appliance where it will be
exposed to the weather.

Do not tamper with controls.

Do not repair or replace any part of the appliance or attempt
any servicing unless specifically recommended in the user-
maintenance instructions or in published user-repair
instructions that you understand and have the skills to carry
out.

Do not use replacement parts that have not been
recommended by the manufacturer (e.g. parts made at
home using a 3D printer).

See the Installation Instructions for grounding requirements
and installation.

This appliance is not designed to be used by people
(including children) with physical, sensory, or mental
abilities reduced, or with lack of experience and knowledge,
unless it has been given instruction or supervision
regarding the use of the appliance.

Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to a
chemical reaction that could cause a load to catch fire. To
reduce the risk of fire due to contaminated loads, the final
part of a tumble dryer cycle occurs without heat (cool down
period). Avoid stopping a tumble dryer before the end of the
drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated.

If the power cord is damaged, it must be replaced by the
manufacturer or its service agent or by qualified personnel
to avoid danger.

New hoses must be used supplied with the appliance, old
hoses they must not be reused to avoid danger.

Do not clean your washing machine with flammable
substances or liquids.

WARNING:

Never stop the Washer-Dryer before the end of

the drying cycle, unless all items are removed quickly and
spread so that the heat dissipates.

Do not use the drying cycle on clothes without a pre-wash.

Remove all items from pockets such as matches and
lighters.

Do not use fabric softeners or products to eliminate static
from clothes unless recommended by the manufacturer of
the fabric softener or the instructions for the product in use.

Do not use heat to dry items that contain foam rubber or
similarly textured rubber materials.

SAVE THESE INSTRUCTIONS

Summary of Contents for 7MWFC6820LC































Reviews: