Wexxar WF-10T Operation And Service Manual Download Page 55

Page: 55 / 156

WF-10T

Case Former

Operating Procedures

6-43

Check the ‘S’ box for Satisfactory Performance and ‘US’ box for Unsatisfactory Performance.

Table 7: Machine Start-up Procedures

Machine Start-up

Start-up Procedures

Select the procedure for the desired mode of operation below:

AUTOMATIC CYCLE Operation:

Press the

‘RESET’

button.

If machine is not in

AUTOMATIC CYCLE

mode, press the

‘MAIN

CONTROL’

button.

Press the

‘START’

button to begin cycling cases.

JOG Operation:

Press the

‘RESET’

button.

If machine is not in

JOG

mode, press the

‘JOG MODE’

button.

Press the

START

button once for each stage in the case forming and

sealing process.

Summary of Contents for WF-10T





























































































































































Search results

Summary of Contents for WF-10T

Reviews:

Related manuals for WF-10T

Brands by name

Popular brands

Wexxar WF-10T, Operation And Service Manual

Search results

Summary of Contents for WF-10T

Reviews:

Related manuals for WF-10T

Brands by name

Popular brands