manualshive.com logo in svg

Wexxar BEL 180, Operator'S Manual

Share
Download
Wexxar BEL 180 Operator'S Manual Download Page 10

B E L   1 8 0   S E M I - A U T O M A T I C   R A N D O M   T A P E   S E A L E R

               

10

 

 

 

Conveyor Side Force [Pressure Regulator] Adjustment 

The force required to center and grip incoming case in the conveyor drive belts may vary 
according to the weight of the product.  The amount of force exerted by the conveyor belts can be 
adjusted by regulating the air pressure in the conveyor case width adjustment mechanism. The 
regulator for the width adjustment is on the left-hand side of the machine behind the main control 
enclosure at the outfeed end. 

Use just enough pressure to center and drive the case effectively. On soft-sided cases, it will 
prevent the case and product from being squeezed unnecessarily.  The recommended pressure 
range is about 

40 PSI.

   

 

The left hand regulator controls the side
belt conveyor case centering and gripping
force.  It should be set in the range of 40
psi for average conditions 

 

65-34-5  4/21/10 

Summary of Contents for BEL 180

















Reviews:

No comments

Brands by name

Popular brands

Load more brands