Westward 15F197 Operating Instructions Manual Download Page 3

3

Problem

Possible Cause

Corrective Action

Grease gun pumps little or no grease

Air is trapped in grease

Prime the grease gun as detailed in the 

section, 

TWO WAYS TO LOAD YOUR 

GREASE GUN

Blocked hose or extension

Remove the hose and operate the 

grease gun. If the gun dispenses 

grease then the gun is fine and you 

need to either clean the hose / exten

-

sion or replace it

Grease too thick or cold

Store grease gun and grease away 

from extreme cold or use thinner 

grease

Excessive grease leaks out from the 

back side of the grease gun around 

the plunger rod

Rubber follower is damaged

Replace the grease gun

Grease leaks from the connection 

between the grease gun head & the 

extension or between extension & 

coupler

Loose connection

Tighten the connection using Teflon or 

any other Thread Sealant

TROUBLESHOOTING

WARRANTY

Should this product fail to perform satisfactorily due to a defect or poor workmanship within ONE YEAR from the date of 

purchase, return it to the place of purchase and it will be replaced, free of charge. Incidental or consequential damages 

are excluded from this warranty.

LIMITED ONE - YEAR WARRANTY

GREASING A GREASE FITTING / GREASE NIPPLE 

1.  The grease coupler provided at the end of the grease 

gun hose has a jaw type construction. The coupler 

jaws will snap on to a grease fitting and maintain a 

tight fit. 

2.  When connecting the coupler to the grease fitting, 

press the coupler straight onto the grease fitting to 

form a snug fit. Start operating the grease gun with 

the coupler as square to the grease fitting as possible. 

3.  Once greasing is completed, slightly tilt the coupler, 

twist and pull back. The tilt and twist action will allow 

easy removal of the coupler from the grease fitting. 

To engage, 
push straight on

To remove,
Tilt, Twist 
& Pull

Grease gun and its hose / extension should be kept clean and checked for damage before each use.

MAINTENANCE

Westward Operating Instructions                                                                                                   15F197, 15F198, 15F199

Lever Grease Guns

Manufactured for Grainger International, Inc.

100 Grainger Pkwy., Lake Forest IL 60045 U.S.A

Summary of Contents for 15F197










Reviews: