manualshive.com logo in svg

Westfalia 84 20 36, Instruction Manual, Page: 12 / 30

Share
Download
Westfalia 84 20 36 Instruction Manual Download Page 12

 

 

8 

Preparation and Use 

Starting the Engine 

1.  Pump the primer bulb (23) repeatedly until the bulb is filled with fuel mix. 
2.  Pull the start/stop switch (17) to the rear position. 
3.  Place the unit on the ground and hold it firmly. 
4.  Use the choke (21) when starting a cold engine. The choke is active with 

the choke lever in the upper position. 

5.  Pull the starter  handle  (22)  vigorously  several times until the engine 

starts. If needed, pump the primer again in order to distribute the fuel. 

6.  After the engine has started, open the choke. Push the choke handle to 

the lower position. 

7.  Allow the engine to warm up at idle speed. 
8.  The engine is equipped with a throttle lock. Always push the throttle (15) 

and the throttle lock (16) simultaneously. 

NOTICE: The choke is not needed for starting a hot engine, e.g. shortly after 

the engine has been shut down. If you needed to use the choke again, 

immediately push it open again after the engine has started. 

Turning Off the Engine 

Release the throttle lever (15) and allow the engine to run at idling speed for a 

few moments.   

Push the start/stop switch (17) to the forward position. 

Maintenance after each Use 

ATTENTION! Before cleaning, inspecting or maintaining the motor unit, make 

sure that engine is  stopped and has cooled down.  The  engine will heat up 

during use. Do not touch the exhaust. There is risk of burns! 
 
 

Summary of Contents for 84 20 36































Reviews:

No comments