Stalker 360 – User’s Manual
V1.0
1
The following is a guide to assist you with the operations & trouble shooting of your new Western Rivers MP 3
electronic game caller. We appreciate you as our customer and wish you the best of success. Good luck and happy
hunting!
STALKER 360 BUTTON PAD & REMOTE BUTTON OPERATIONS
POWER BUTTON:
The “Power” button on the game caller is designed to manually turn your game
caller to ON or OFF status. By pressing and holding the button down for a few seconds you will turn the
unit on. The Western Rivers welcome screen with come up and then go to your library list. If you want
to turn the unit off, you must press & hold down this button until the display goes to a blank screen and is no
longer illuminated. The power button on the remote control functions the same way as the game caller.
This
button is designed to put the caller into a “Standby Mode” while in use!
This button will not power off the
game caller.
The battery will discharge if you fail to manually turn unit off on the main button pad. (See Battery
Maintenance) The game caller must be turned on before you can control it with the remote.
The “Power” button on the Remote Control unit is designed to remotely turn the game caller to the ON or
STANDBY status only from a remote location. Press the button on the remote once to turn unit ON, press & hold
to power game caller OFF. When game caller is in a standby mode, it is operating on minimum battery
consumption. If power button doesn’t appear to work on either unit, please check the battery and replace. Low
battery level will also affect the operation of the button pad. Make sure that game caller is showing a full to half
battery cycle life before taking it to the field. (See Battery Maintenance).
IMPORTANT NOTE:
The game caller will need to be
connected to the remote after you upload or delete
ANY sounds into the systems hard drive so that
the remote can recognize the new order of the playlist
selections
(See Downloads & Uploads).
PLAY / ENTER BUTTON:
The “Play” button on both units will
start
the pre-selected sound you have
chosen. The “Play” button on either unit can be activated by firmly pressing the button. Press & hold is
not required. You can also play two different sounds out of the speakers. In order to do this you need to
choose your first selected sound. Once sound is playing press the Previous button to go back to the playlist and
select and play your second sound. This icon also acts as the “Enter” button, so if you want to go back or make a
selection choice you’d press this button. If either “Play” button on either unit appears not to work, check the
battery for status. If you use the button pad on the game caller to operate the functions of the caller, the LCD on the
remote control
will not
show the same information.
Requests transmitted from the remote control
will be
shown on
the game caller’s LCD.
PAUSE BUTTON:
The “Pause” button on both units will
pause
the play of the current sound selected.
If the “Pause” button appears not to work on either unit, check the battery for status. By pressing the
PLAY
button will restart the paused sound at the exact same location it was paused at.
The volume of the unit will automatically resume at the same level as previous setting when this function is
activated. If you use the button pad on the game caller to operate the functions of the caller, the LCD on the remote
control
will not
show the same information.
Requests transmitted from the remote control
will be
shown on the
game caller’s LCD.
NEXT BUTTON:
The “Next” button on both units allows the user to scan in a downward motion to
arrive at the desired sound to play that is seen on the LCD. To activate, firmly press and release for each
scan to the next selection. Press & hold will scan the entire selection.
For best results rename and reload
sounds in your special grouping. If the “Next” button appears not to work on either unit, check the battery for
status. If you use the button pad on the game caller to operate the functions of the caller, the LCD on the remote
control
will not
show the same information.
Requests transmitted from the remote control
will be
shown on the
game caller’s LCD.
PREVIOUS BUTTON:
The “Previous” button on both units allows the user to scan in a upward
motion to arrive at the desired sound to play that is seen on the LCD. To activate, firmly press and
release for each scan to the previous selection. Press & hold will scan the entire selection.
For best
results rename and reload sounds in your special grouping. If the “Previous” button appears not to work on either
unit, check the battery for status. If you use the button pad on the game caller to operate the functions of the caller,
the LCD on the remote control
will not
show the same information.
Requests transmitted from the remote control
will be
shown on the game caller’s LCD.
NEXT 10 BUTTON:
The “Next 10” button recalls ten (10) sounds at once thus allowing you to
instantly scan through your entire library of sounds in the order they were loaded very quickly. The
