Western Digital NETCENTER User Manual Download | Manualshive

Page: 41 / 63

background image

NETCENTER MANAGER – 37

NETCENTER

USER MANUAL

Printer Sharing

1. Click

Printer Sharing

. The screen displays the printer(s) attached to the NetCenter.

2. Click

Apply

.

3. Follow the printer driver installation instructions for Windows or Mac below.

Windows

The following printer sharing instructions are provided for Windows 2000/XP/2003 only.
Printer information for Windows operating systems can be obtained from our Technical
Support site at

support.wdc.com

1. On the

Start

menu, click

Printers and Faxes

.

2. Click

Add a Printer

, then click

Next

.

«
...
39
40
41
42
43
...
»

Summary of Contents for NETCENTER
































































Reviews:

No comments

Related manuals for NETCENTER

Brand: Magnat Audio Pages: 2

Brand: Magnadyne Pages: 13

Brand: Watchguard Pages: 39

Brand: TP-Link Pages: 2

Brand: NetBurner Pages: 30

WISENET XRN-1610

Brand: Hanwha Techwin Pages: 88

RuggedNet 10G/Si

Brand: OST Pages: 8

Brand: Hameg Pages: 46

Application Module 9109 OCU-DP

Brand: Paradyne Pages: 8

AN5506-04 Series

Brand: FiberHome Pages: 146

Turbo 16/4 Token-Ring PC Card 2

Brand: IBM Pages: 123

Brand: National Instruments Pages: 72

Brand: Advantage Pages: 4

Brand: Infrapower Pages: 36

Brand: CYP Pages: 16

Brand: Asus Pages: 21

Brand: Asus Pages: 2

Brand: Asus Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands