Westell PROACT 3115-80, Manual

Page: 23 / 26

Section 311-580-20B
030-101527 Rev. B
23
0407IBRB
Appendix A -
Remote Provisioning Codes
Field Parameter De-
fault
TL1 Command & Response
(See Note 1)
16-Bit Code
(See Note 2)
Hex Code Bit Error
Response
Monitored Line
C di
AMI WSTMONLC=AMI 1100 0101 1011 0001 C5B1
Coding
B8ZS WSTMONLC=B8ZS 1100 0101 1011 0010 C5B2
Monitored Framing SF WSTMONFRMG=SF 1100 0100 1101 0001 C4D1 g
ESF WSTMONFRMG=ESF 1100 0100 1101 0010 C4D2
CPE LOS Response None WSTCLOSRSP=NONE 1100 0101 1010 0001 C5A1 p
LB WSTCLOSRSP=LB 1100 0101 1010 0010 C5A2
AIS WSTCLOSRSP=AIS 1100 0101 1010 0011 C5A3
Idle WSTCLOSRSP=Idle 1100 0101 1010 0100 C5A4
AIS-CI WSTCLOSRSP=AIS-CI 1100 0101 1010 0101 C5A5
RAI-CI Operation Disabled WSTRAICI=DIS 1100 0101 1010 0110 C5A6 p
Enabled WSTRAICI=ENA 1100 0101 1010 0111 C5A7
Real-Time PM Mode None WSTRTPM=NONE 1100 0101 1101 0001 C5D1
NPRM WSTRTPM=NPRM 1100 0101 1101 0010 C5D2
SPRM WSTRTPM=SPRM 1100 0101 1101 0011 C5D3
SPRM/NPRM WSTRTPM=NSPRM 1100 0101 1101 0100 C5D4
CPE REGEN
(FAC CPE)
Regen Off WSTRCVRGN=DIS 1100 0100 1010 0001 C4A1
(FAC-to-CPE)
Regen On WSTRCVRGN=ENA 1100 0100 1010 0010 C4A2
FAC REGEN
(CPE FAC)
Regen Off WSTTRMTRGN=DIS 1100 0100 1011 0001 C4B1
100
(CPE-to-FAC)
Regen On WSTTRMTRGN=ENA 1100 0100 1011 0010 C4B2
XMT LBO
0 dB WSTTRMTLBO=0 1100 0100 1011 0011 C4B3
(CPE-to-FAC)
7.5 dB WSTTRMTLBO=7.5 1100 0100 1011 0100 C4B4
(CPE-to-FAC)
15 dB WSTTRMTLBO=15 1100 0100 1011 0101 C4B5
22.5 dB WSTTRMTLBO=22.5 1100 0100 1011 0110 C4B6
AB15 dB WSTTRMTLBO=AB15 1100 0100 1011 0111 C4B7
AB22.5 dB WSTTRMTLBO=AB22.5 1100 0100 1011 1000 C4B8
FAC-to-CPE LBO
0 dB WSTRCVLBO=0 1100 0100 1010 0011 C4A3
7.5 dB WSTRCVLBO=7.5 1100 0100 1010 0100 C4A4
15 dB WSTRCVLBO=15 1100 0100 1010 0101 C4A5
Loopback Mode Normal WSTLBMODE=NORM 1100 0101 1111 0011 C5F3 p
Addressed WSTLBMODE=ADDR 1100 0101 1111 0100 C5F4
Loopback Time-out
Enable 20 WSTLBTO=20 1101 0101 1101 0001 D5D1
p
Enable 60 WSTLBTO=60 1101 0101 1101 0010 D5D2
Enable 120 WSTLBTO=120 1101 0101 1101 0011 D5D3
Enable 1440 WSTLBTO=24HR 1101 0101 1101 0100 D5D4
Disable WSTLBTO=DIS 1101 0101 1101 0110 D5D6
Reset to Default Reset WSTSDEF= 1100 0101 0111 0110 C576
Circuit ID ASCII string up to 20 char. WSTCKTID=<ASCIIstring> N/A N/A
Note 1:
TL1 commands are transmitted in the Facility Data Link (FDL) using the command SND-CMD-FDL via the LAPB protocol. The command used to provision the unit is:
ED-T1:::<CTAG>:::<OPTNM>-<OPTSTG>;. Example of the TL1 command to change the XMT LBO of the unit is: ED-T1::::::WSTTXLBO=7.5; The unit then will respond to the
command with TL1 command in this example 7.5.
Note 2:
All 16-bit command codes must be sent to the unit for minimum of five seconds in order to provision the unit. In order to see a bit-error response from the unit, the command code
must be present for a minimum of 10 seconds. The unit will respond to the command with bit errors after the 10-second time frame.
Table 11. Remote Provisioning Codes