Wenger Legacy Classic Assembly Instructions Manual Download Page 1

Assembly Instructions

Legacy

®

Classic Acoustical Shell

Note:

Please read and understand these Assembly Instructions for the Legacy Classic Acoustical
Shell before assembling the parts.

Note:

Refer to the illustrations on the following pages. If you need additional information, write or
telephone Wenger Corporation at the number below.

c

ontents

©Wenger Corporation 2011

Printed in USA 10/11

Part #186H191-01

Wenger Corporation,

555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448

Questions? Call.....USA: 800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com

Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . .2

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Manufacturer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Intended Use  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Warranty  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Safety Precautions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Required Tools  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Before Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Assembly  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Summary of Contents for Legacy Classic









Reviews: